Black & Decker GL710 Manuel d'instructions télécharger pdf (Page 8)

ENGLISH

♦ Place the new spool onto the boss in the spool

housing with the lines parked in the slots (23)

(ﬁ g. F).

♦ Insert the line ends through the appropriate

eyelets (20) in the housing (10). Pull the slack

line until it pulls out of the parked slots (23)

(ﬁ g. G).

♦ Align the tabs (17) on the spool cover with the

cut outs (21) in the housing.

♦ Push the cover (18) onto the housing (10) until

it snaps securely into place.

Note: Make sure that the cover is positioned,

listen for two audible clicks to ensure both tabs

(17) are correctly located.

Warning! If the cutting lines protrude beyond the

trimming blade (9), cut them off so that they just

reach the blade.

Winding new line onto an empty spool

(ﬁ g. H - J)

You may wind new cutting line onto an empty

spool.

Replacement packs of cutting line are available

from your Black & Decker dealer (cat. no. A6171).

♦ Remove the empty spool from the appliance as

described above.

♦ Remove any remaining cutting line from the

spool.

♦ First wind new line onto the uppermost part of

the spool:

- Feed 2 cm of cutting line into one of the

slots in the upper section of the spool as

shown.

- Wind the cutting line onto the spool in the

direction of the arrow. Make sure to wind

the line on neatly and in layers. Do not

criss-cross.

- When the wound cutting line reaches the

recesses (22), cut the line.

- Temporarily park the line in the slots (23)

on one side of the spool as shown.

♦ Repeat the above procedure for the second

cutting line on the lower section of the spool.

Park the line in the unused slots (23).

♦ Proceed as described above to ﬁ t the spool

on the appliance. Do not forget to release the

cutting line from the parking slots (23).

Warning! Only use the appropriate type of

Black & Decker cutting line. Ensure that cutting

line is present in both sections of the spool.

Mains plug replacement

(U.K. & Ireland only)

If a new mains plug needs to be ﬁ tted:

♦ Safely dispose of the old plug.

♦ Connect the brown lead to the live terminal in

the new plug.

♦ Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the

earth terminal. Follow the ﬁ tting instructions

supplied with good quality plugs. Recommended

fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow

the instructions below. If this does not solve the

problem, please contact your local Black & Decker

repair agent.

Warning! Before proceeding, unplug the tool.

Appliance runs slowly

♦ Check that the spool housing can rotate freely.

Carefully clean it if necessary.

♦ Check that the cutting line does not protrude

more than 11 cm from the spool housing. If it

does, cut it off so that it just reaches the line

trimming blade.

Automatic line feed does not work

♦ Keep the tabs depressed and remove the

spool cover from the housing.

♦ Pull the cutting line until it protrudes 11 cm

from the housing. If insufﬁ cient cutting line is

left on the spool, install a new spool of cutting

line as instructed above.

♦ Align the tabs on the spool cover with the cut

outs in the housing.

♦ Push the cover onto the housing until it snaps

securely into place.

♦ If the cutting line protrudes beyond the

trimming blade, cut it off so that it just reaches

the blade.

If the automatic line feed still does not work or the

spool is jammed, try the following suggestions:

♦ Carefully clean the spool cover and housing.

♦ Remove the spool and check if the lever can

move freely.

♦ Remove the spool and unwind the cutting

line, then wind it on neatly again as described

above. Replace the spool as instructed.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GL710 Manuel d'instructions Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker GL710