Black & Decker GL710 Manuel d'instructions télécharger pdf (Page 6)

6

ENGLISH

♦ Wear long trousers to protect your legs.

♦ Before using the appliance, check that your

cutting path is free from sticks, stones, wire

and any other obstacles.

♦ Only use the appliance in the upright position,

with the cutting line near the ground. Never

switch the appliance on in any other position.

♦ Move slowly when using the appliance. Be

aware that freshly cut grass is damp and

slippery.

♦ Do not work on steep slopes. Work across the

face of slopes, not up and down.

♦ Never cross gravel paths or roads while the

appliance is running.

♦ Never touch the cutting line while the appliance

is running.

♦ Do not put the appliance down until the cutting

line has come to a complete standstill.

♦ Use only the appropriate type of cutting line.

Never use metal cutting line or ﬁ shing line.

♦ Be careful not to touch the line trimming blade.

♦ Take care to keep the mains cable away

from the cutting line. Always be aware of the

position of the cable.

♦ Keep hands and feet away from the cutting line

at all times, especially when switching on the

motor.

♦ Before using the appliance and after any

impact, check for signs of wear or damage and

repair as necessary.

♦ Never operate the appliance with damaged

guards or without guards in place.

♦ Take care against injury from any device ﬁ tted

for trimming the ﬁ lament line length. After

extending new cutter line always return the

machine to its normal operating position before

switching on.

♦ Always ensure that the ventilation slots are

kept clear of debris.

♦ Do not use the lawn trimmer (edge trimmer), if

the cords are damaged or worn.

♦ Keep extension cords away from cutting

elements.

Labels on appliance

The following warning symbols are found on the

appliance:

Read the manual prior to operation.

Wear safety glasses or goggles when

operating this appliance.

Keep people and animals at least 6 m

away from the cutting area.

Do not expose the appliance to rain or

high humidity.

Electrical safety

This appliance is double insulated;

therefore no earth wire is required. Always

check that the power supply corresponds

to the voltage on the rating plate.

♦ If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised

Black & Decker Service Centre in order to

avoid a hazard.

Features

This appliance includes some or all of the

following features.

1. On/off switch

2. Handle

3. Cable restraint

4. Power inlet

5. Secondary handle

6. Adjustment button

7. Tube

8. Guard

9. Line trimming blade

10. Spool housing

11. Cutting line

12. Edge guide

Assembly

Warning! Before assembly, make sure that the

appliance is switched off and unplugged.

Fitting the guard (ﬁ g. A)

♦ Remove the hexagonal screws (13) from the

head (14).

♦ Place the guard (8) onto the appliance as

shown.

♦ Firmly press the guard until it snaps into place.

♦ Secure the guard with the hexagonal screws.

♦ Tighten the hexagonal screws using the

hexagonal key (15) provided.

Warning! Never use the appliance unless the

guard is properly ﬁ tted.

Releasing the cutting line

In transit, the cutting line is taped to the spool

housing.

♦ Remove the tape holding the cutting line (11)

to the spool housing (10).

Connecting the appliance to the mains

♦ Connect the female plug of a suitable

extension cable to the power inlet (4).

♦ Loop the cable through the cable restraint (3).

1 2 3 4 5 6 7 8 9 10 11 ... 75 76

Commentaires sur ces manuels

Pas de commentaire