Black & Decker GL300 Manuel d'instructions télécharger pdf (Page 15)

ENGLISH

Trimming Technique and Performance Notes

Tilt trimmer at a slight angle from the ground. Lower to grass or

weeds you intend to cut. (If they are over 20cm (8") high, start

cutting at top.) Slowly swing unit into and out of area being cut,

holding the unit off the ground at desired cutting height.

IMPORTANT— for the best cutting action against walls, fences

and in high grass, move trimmer slowly so grass is cut WITH

THE TIP of the high speed nylon line.

1. Avoid running trimmer with hub in contact with ground.

2. Trim only when grass and weeds are dry.

3. The life of your nylon line is dependent upon following the

above trimming techniques, as well as what is being cut,

and where the cutting is being done.

EXAMPLE: Line will wear faster when run against a foundation

wall as compared to trimming around a tree. Some line breakage

will occur from feeding unit too fast, from entanglement with

foreign matter, from normal line fatigue, and from attempting to

cut thick, stalky weeds in excess of unit’s capability.

Note: As the weather becomes cooler, the tendency for the

nylon line to break becomes greater.

DO NOT USE UNIT WHEN TEMPERATURE IS BELOW 50° F

4. For best performance, as the line wears, lengthen as

indicated in Line Feeding Procedure.

5. Periodically unplug extension cord at trimmer and remove

the accumulation of grass or cutting debris from the inside

of the bump cap shroud.

Spool Replacement and Recovery of Line Broken Off

Inside Spool

1. Unplug the tool. Remove cap by pushing the two tabs in

and up, then lift off. (It is not necessary to push both tabs in

at the same time).

2. Remove any debris and grass buildup that may be inside

the cap and on the inside of the hole in the cap.

3. Remove spool by aligning he notch on the edge of the spol

with the eyelet in the hub and wipe any dirt off the ribs on

the shaft.

4. Unwind about 3” of line from the spool and hold it in one of

the two notches. Make sure spring is in place on the hub.

5. Holding the line in the gap, insert the end through the eyelet

in the hub and slip the spool into the hub. If the spool does

not slip into the hub easily, press gently and pull straight out

on the cutting line that protrudes through the eyelet.

6. Install cap by pushing both snap legs into the hub at once.

Make sure that both legs are snapped in one place. Pull line

out by hand until tight.

7. The line should extend out no further than the guard. You

are now ready to resume trimming.

8. The cutoff blade will automatically-trim excess line to the

proper length.

MAINTENANCE

Unplug Extension Cord at Trimmer

Maintain Tool With Care

1. Keep the air intake slots clean to avoid overheating which

will damage trimmer. For this cleaning, use a dry brush or

cloth to remove grass, sap or other debris.

2. Plastic parts may be cleaned by using a mild soap and a rag

dampened with hot water. Avoid all other types of detergents,

cleaners or solvents which might contain chemicals that could

seriously damage the plastic. Do not spray the trimmer with

water.

3. Self lubricating bearings are used in the tool and periodic

relubrication is not required. However, it is recommended

that after two or three seasons of use, you take or send the

trimmer to a Black & Decker service center or authorized

service station (see TOOLS, ELECTRIC in yellow pages)

for a thorough cleaning, inspection and relubrication. If the

tool is being used professionally, the above should be

accomplished after each trimming season.

4. If trimmer fails to operate, disconnect extension cord from

power source first, then from trimmer. Make sure extension

cord is undamaged and that house fuses are not blown or

circuit breakers tripped. If trimmer still fails to operate, take

or send it to your local B&D service center or authorized

service station for repair. Do not attempt to repair it yourself.

IMPORTANT

To assure product SAFETY and RELIABILITY, repairs,

maintenance and adjustment (including brush inspection and

replacement) should be performed by authorized service centers

or other qualified service organizations, always using identical

replacement parts.

ACCESSORIES

Replacement line is available from your local dealer, or a Black

& Decker service center.

Recommended accessories for your trimmer are shown in this

manual. The use of any other accessory or attachment might be

hazardous.

RS300 Replacement Spool with 10 feet of Nylon Line.

Caution! Use only recommended accessories with

your string trimmer. The use of any other attachment

or accessory might be hazardous. Use only specially

treated. 0.065” diameter nylon line.

1 2 ... 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GL300 Manuel d'instructions Page 15

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker GL300