Black & Decker KX1650 Manuel d'instructions télécharger pdf (Page 5)

ENGLISH

(Original instructions)

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Labels on tool

The following pictograms are shown on the tool:

;

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Extension cables

u A 2 or 3 core cable may be used as the appliance is

double insulated and of class II construction.

u Up to 30m (100 ft) can be used without loss of power.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Nozzle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting an accessory

A selected range of accessories can be obtained from your

local retailer.

w Cone nozzle: Concentrates the air stream on a smaller

area.

w Fish tail: Spreads the air stream over a wider area

w Spoon reector: For soldering pipes.

w Glass protector: For the protection of glass during paint

stripping.

w Scraper: For the removal and stripping paint and

varnish.

u Fit the connecting piece of the accessory over the nozzle

(2).

Use

Switching on and off

u To switch the tool on at the low air speed, low heat, set the

on/off switch to position I.

u To switch the tool on at the high air speed, high heat, set

the on/off switch to position II.

u To switch the tool off, set the on/off switch to position O.

Using the tool

Your tool is tted with a thermostat for your safety. Using the

tool continuously for very long periods or other severe duty

cycles may cause the tool to overheat and stop working. It is

therefore recommended that you allow the tool to cool down at

regular intervals during use.

u Allow the tool to heat up for a few seconds before use.

u At rst use some smoke may emit from the nozzle. This is

normal and will soon decrease.

u Use a low temperature setting for drying paint and varnish,

removing stickers, shrinking insulation tubes, and thawing

frozen pipes.

u Use a high temperature setting for removing paints and

lacquers, and soldering plumbing joints.

u If you are unsure about using this tool on a particular

material, start with a low temperature setting and perform

a test on scrap material.

Hands free use (g. A)

The tool has stand locations (3) to facilitate hands free use.

u Place the tool with the nozzle up on a surface where it

cannot be tipped over.

u Secure the cable to prevent pulling the tool over.

Warning! Always point the tool away from yourself or other

persons. Do not touch the nozzle. Take care that no material

drops into the nozzle.

Paint stripping

u Direct the hot air at the working area to heat up the paint.

u Do not burn the paint. Keep the nozzle at least 25 mm

from the surface.

u When the paint softens, remove the paint using a scraper.

Scrape the softened paint immediately or it will harden

again.

u Scrape with the grain of the wood wherever possible.

u Do not allow paint and debris to collect on the scraper.

u When scraping from a vertical position, scrape downwards

to prevent the paint from falling back into the nozzle.

u When stripping paint from a surface next to glass, take the

necessary measures to protect the glass from the heat.

1 2 3 4 5 6 7 8 9 10 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Black & Decker KX1650 Manuel d'instructions Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker KX1650