Black & Decker HP142K(D) Manuel d'instructions télécharger pdf (Page 11)

HP12KD/HP14KD/HP122KD/HP142KD -

Attaching the detector (fig. K)

The tool provides a mounting location where the

detector (23) is stored when not in use.

◆ Hang the unit to the holder (24) as shown.

USE

Let the tool work at its own pace.

Do not overload.

Charging the battery

The battery needs to be charged before first use

and whenever it fails to produce sufficient power

on jobs that were easily done before.

When charging the battery for the first time, or

after prolonged storage, it will only accept an 80%

charge. After several charge and discharge cycles,

the battery will attain full capacity. The battery

may become warm while charging; this is normal

and does not indicate a problem.

Do not charge the battery at ambient

temperatures below 4 °C or above 40 °C.

Recommended charging temperature:

approx. 24 °C.

HP96K/HP12K(D)/HP14K(D) (fig. D)

◆ To charge the battery (9), remove it from the

tool.

◆ Slide the charger receptacle (12) onto the

battery as shown.

◆ Plug in the charger (11).

The battery will become warm while charging.

After approx. 3 hours of charging, the battery will

be fully charged.

◆ Remove the charger receptacle from the

battery.

HP122K(D)/HP142K(D) (fig. E)

◆ To charge the battery (9), remove it from the

tool and insert it into the charger (13).

The battery will only fit into the charger in one

way. Do not force. Be sure that the battery is

fully seated in the charger.

◆ Plug in the charger.

◆ Check if the red charging indicator (14) lights up.

If the green end of charge indicator (15) lights

up now instead, the battery is too hot and

cannot be charged. If this happens, remove

the battery from the charger, let the battery

cool down for approx. 1 hour and

re-insert it.

After approx. 1 hour of charging, the red charging

indicator (14) will stop lighting and the green end

of charge indicator (15) will light up. The battery is

now fully charged.

◆ Remove the battery from the charger.

HP96K/HP12K/HP14K/HP122K/HP142K -

Checking the battery condition (fig. F)

This tool is fitted with a battery charge indicator,

which allows you to check the condition of the

battery.

◆ Press and hold down the button (19).

◆ Check to see how many of the lights (20) are

on:

Battery charge

1 light low

2 lights medium

3 lights high

Selecting the direction of rotation (fig. G)

For drilling and for tightening screws, use forward

(clockwise) rotation. For loosening screws or

removing a jammed drill bit, use reverse

(counterclockwise) rotation.

◆ To select forward rotation, push the forward/

reverse slider (2) to the left.

◆ To select reverse rotation, push the forward/

reverse slider to the right.

◆ To lock the tool, set the forward/reverse slider

into the centre position.

Selecting the operating mode or torque (fig. H)

This tool is fitted with a collar to select the

operating mode and to set the torque for

tightening screws. Large screws and hard

workpiece materials require a higher torque

setting than small screws and soft workpiece

materials. The collar has a wide range of settings

to suit your application.

◆ For drilling in wood, metal and plastics, set the

collar (3) to the drilling position by aligning the

symbol with the marking (21).

ENGLISH

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 103 104

Commentaires sur ces manuels

Pas de commentaire

Black & Decker HP142K(D) Manuel d'instructions Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker HP142K(D)