Black & Decker PSL12 Manuel d'utilisateur télécharger pdf (Page 5)

USING THE CLAW (FIGURE F)

To release claw (7):

• Pull back on claw release button (5). This

will release the claw. Once claw is

released you can let go of button.

• Push in on lock-off button (4) and

squeeze the on/off switch (3).

• With the saw running, the claw will rotate

forward until it comes in contact with the

workpiece.

• Once the cut is complete, the claw will

rotate fully back to the stop position.

BLADE INSTALLATION AND REMOVAL (FIGURE G)

CAUTION: Make sure the lock-off button is engaged to prevent switch actuation

before making any adjustments or removing or installing attachments or accessories.

The blade should extend past the shoe and the thickness of the workpiece during the

cut. Select the blade best suitable for the material to be cut and use the shortest blade

suitable for the thickness of the material.

WARNING: Cut hazard. Blade breakage may occur if the blade does not extend past

the shoe and the workpiece during the cut. Increased risk of personal injury, as well as

damage to the shoe and workpiece may result.

TO INSTALL BLADE INTO SAW

1. Point tool away from body.

2. Rotate blade clamp release lever (8) in the

direction shown in figure G.

3. Insert blade shank fully into blade clamp.

4. Release blade clamp release lever (8) to

lock blade into position.

TO REMOVE BLADE FROM SAW

WARNING: Burn hazard. Do not touch

the blade immediately after use. Contact with

the blade may result in personal injury.

1. Rotate blade clamp release lever (8) in the

direction shown in figure G.

2. Remove blade.

3. Release the blade clamp release lever (8).

ASSEMBLY INSTRUCTIONS

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

WARNING: Make certain the lock-off button is engaged to prevent switch actuation

before removing or installing battery.

TO INSTALL BATTERY PACK: Insert battery

pack into tool, until an audible click is heard

as shown in figure B.

TO REMOVE BATTERY PACK: Depress the

battery release buttons as shown in figure C

and pull battery pack out of tool.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

OPERATING INSTRUCTIONS

WARNING: Always wear proper eye, respiratory and hearing protection while

operating this tool.

• Use clamps or another practical way

to secure and support the workpiece

to a stable platform. Holding the work

by hand or against your body leaves it

unstable and may lead to loss of control.

• Place shoe firmly against work to be cut.

• Hold the tool with one hand as shown in

figure D. Switch on saw motor and allow

it to obtain maximum speed before

applying pressure.

TRIGGER SWITCH (FIGURE E)

The tool is equipped with a switch lock-off feature to prevent unintentional operation.

• To switch the tool on, press the lock off

button (4) as shown in figure E, then

squeeze the on/off switch (3).

• Once the tool is on, release the lock off

button.

• Releasing the trigger turns the motor OFF.

NOTE: This tool has no provision to lock

the switch in the ON position, and should

never be locked in the ON position by any

other means.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and the receiver.

. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

8 9

1 2 3 4 5 6 7 8 9 10 ... 20 21

Commentaires sur ces manuels

Pas de commentaire

Black & Decker PSL12 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker PSL12