Black & Decker LI2000 Manuel d'instructions télécharger pdf (Page 7)

OPERATING INSTRUCTIONS

•Donotusescrewdriverasaprybarinany

position.

•Toavoidscrewdriverbeingturnedon

accidentally, do not carry in your pocket.

OPERATING IN POWER MODE

Forward

•Rotatethecollar(4)tothepositionmarked

as shown in figure F.

•Slidetheforward/reverseswitch(1)tothe

right, exposing the arrow pointing forward

as shown in figure F.

•Pressthebuttonontheswitchandthetoolwill

run; release the button and the tool will stop.

Reverse

•Rotatethecollar(4)tothepositionmarked

as shown in figure F1.

•Slidetheforward/reverseswitch(1)tothe

left, exposing the arrow pointing backward.

•Pressthebuttonontheswitchandthetoolwill

run; release the button and the tool will stop.

FORWARD/REVERSE/LOCK-OFF SLIDER

•Whentheforward/reverseslider(1)isinthe

central position the tool is locked off to prevent

accidental actuation or battery discharge.

OPERATING IN MANUAL MODE

•Rotatethecollartothepositionmarked

as shown in figure G.

•Usethetoolasanyconventionalnon-

powered screwdriver. When the forward /

reverse slider (1) is in the central position

the tool is locked off to prevent accidental

actuation or battery discharge.

NOTE: If the collar fails to move past the

cental lock position to manual mode then

please see the following procedure:

1. Turn clutch collar to Power Mode .

(figure G1)

2. Run the unit.

4. Turn clutch collar to Manual Mode .

(figure G1)

SCREW DRIVING

•Beforeinstallingbits,movetheforward/reverse

slider(1)tothecenter“lock-off”position.

•Inserttheappropriatehexshank

screwdriver bit into the spindle.

•Selectforwardorreverserotation.

DRILLING

•Beforeinstallingbits,movetheforward/reverse

slider(1)tothecenter“lock-off”position.

•Inserttheappropriatehexshankdrillbit.

•Selectforwardrotation.

NOTE: When drilling, the bit may become

disconnected from the spindle upon

withdrawing it from the material. Should

this occur, the bit can be removed by

re-insertingthehexshankintothespindle

and running the tool in the reverse direction.

GENERAL DRILLING TIPS

•Thistoolisnotrecommendedfordrilling

in masonry.

•Usesharpdrillbitsonly.

•Drillbitsformetalcanbeusedfordrilling

holes in wood. These bits must be sharp

and should be pulled out frequently when

drilling to clear chips from the flutes.

•Supportandsecureworkproperly,as

instructed in the safety Instructions.

•Useappropriateandrequiredsafety

equipment, as instructed in the safety

instructions.

•Secureandmaintainworkarea,as

instructed in the safety instructions.

•Applypressureinastraightlinewiththe

bit. Use enough pressure to keep the

bit biting but not so much as to stall the

motor or deflect the bit.

•Holdthetoolfirmlytocontrolitstwistingaction.

•DONOTCLICKTHETRIGGEROFA

STALLED TOOL OFF AND ON IN AN

ATTEMPT TO START IT. DAMAGE TO

THE TOOL CAN RESULT.

•Minimizestallingonbreakthroughby

reducing pressure and slowly drilling

through last part of hole.

•Keepthemotorrunningwhilepullingthebitout

of a drilled hole. This will help reduce jamming.

•Makesureswitchturnstoolonandoff.

WARNING: It is important to support

work properly and to hold the tool firmly to

prevent loss of control which could cause

personal injury.

MAINTENANCE

Use only mild soap and damp cloth to

clean the tool. Never let any liquid get

inside the tool; never immerse any part of

the tool into a liquid.

IMPORTANT: To assure product SAFETY

and RELIABILITY, repairs, maintenance

and adjustment (other than those listed

in this manual) should be performed by

authorized service centers or other qualified

service personnel, always using identical

replacement parts.

Thisproductuseslithium-ionrechargeable

and recyclable batteries. When the batteries

no longer hold a charge, they should be

removed from the product and recycled.

They must not be incinerated or composited.

The batteries can be taken for disposal

toaBlack&Decker,Company-Owned

or Authorized Service Center. Some

local retailers are also participating in a

national recycling program (see “RBRC™

BATTERY REMOVAL AND DISPOSAL

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Black & Decker LI2000 Manuel d'instructions Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker LI2000