Black & Decker FIRESTORM FS210LS Manuel d'instructions Page 27
- Page / 68
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
27
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! SAW WILL NOT START
WHAT’S WRONG? WHAT TO DO…
1.Saw not plugged in. 1.Plug in saw.
2.Fuse blown or circuit breaker tripped. 2.Replace fuse or reset
circuit breaker.
3.Cord damaged. 3.Have cord replaced by
authorized service center.
4.Brushes worn out. 4.Have brushes replaced
by authorized service center.
TROUBLE! SAW MAKES UNSATISFACTORY CUTS
WHAT’S WRONG? WHAT TO DO…
1.Dull blade. 1.Replace blade.
2.Blade mounted backwards. 2.Turn blade around.
3.Gum or pitch on blade. 3.Remove blade and
clean with turpentine.
4.Incorrect blade for work being done. 4.Change the blade.
TROUBLE! BLADE DOES NOT COME UP TO SPEED
WHAT’S WRONG? WHAT TO DO…
1.Extension cord too light or too long. 1.Replace with adequate
size cord.
2.Low house current. 2.Contact your electric
company.
TROUBLE! MACHINE VIBRATES EXCESSIVELY
WHAT’S WRONG? WHAT TO DO…
1.Stand on uneven floor. 1.Reposition on flat level
surface.
2.Damaged saw blade. 2.Replace blade.
TROUBLE! DOES NOT MAKE ACCURATE MITER CUTS
WHAT’S WRONG? WHAT TO DO…
1.Miter scale not adjusted correctly. 1.Check and adjust.
2.Blade is not square to fence. 2.Check and adjust.
3.Blade is not perpendicular to table. 3.Check and adjust fence.
4.Workpiece moving. 4.Clamp workpiece to
fence or glue 120 grit
sandpaper to fence with
rubber cement.
TROUBLE! MATERIAL PINCHES BLADE
WHAT’S WRONG? WHAT TO DO…
1.Cutting bowed material. 1. Position bowed material
with concave or hollow side down.
2.Rip fence not parallel to blade. 2. Realign rip fence.
TROUBLE! CANNOT LOCK BLADE INTO BEVEL POSITION
WHAT’S WRONG? WHAT TO DO…
1.Blade tilting lock handle too loose. 1.Remove blade raising and lowering with
handwheel.
2. Remove flat head screw from lock handle.
3. Tighten blade tilting lock handle. The lock
handle (A) is spring-loaded and can be
repositioned by pulling out on the handle (A)
and repositioning it on the serrated stud
located underneath the handle. NOTE: After
tightening, place the handle at the one o’clock
position.
4. Replace the flat head screw.
TROUBLESHOOTING GUIDE
- INSTRUCTION MANUAL 1
- GENERAL SAFETY RULES 2
- ADDITIONAL SAFETY RULES FOR 4
- TABLE SAWS 4
- POWER CONNECTIONS 5
- MOTOR SPECIFICATIONS 5
- GROUNDING INSTRUCTIONS 5
- EXTENSION CORDS 6
- FUNCTIONAL DESCRIPTION 6
- ILLUSTRATE TECHNIQUE ONLY 7
- STAND PARTS 9
- MITER GAGE HOLDER 10
- STAND ASSEMBLY 11
- ATTACHING DUST BAG 11
- SAW TO STAND 11
- ASSEMBLING BLADE 12
- RAISING AND LOWERING 12
- HANDWHEEL 12
- SPLITTER ASSEMBLY 13
- BLADE GUARD AND 13
- EXTENSION WINGS 15
- GUIDE RAIL TO SAW 15
- RIP FENCE 16
- MITER GAGE 16
- OUTFEED SUPPORT 17
- STARTING AND STOPPING SAW 18
- LOCKING SWITCH IN THE “OFF” 18
- POSITION 18
- BLADE RAISING AND 18
- LOWERING CONTROL 18
- RIP FENCE OPERATION 20
- AND ADJUSTMENTS 20
- ADJUSTING BLADE PARALLEL TO 21
- MITER GAGE SLOTS 21
- CHANGING THE BLADE 21
- COMMON SAWING OPERATIONS 22
- USING AUXILIARY WOODFACING ON 24
- ACCESSORY DADO CUTTERHEAD 24
- CONSTRUCTING A FEATHERBOARD 26
- TROUBLESHOOTING GUIDE 27
- PUSH STICK 28
- ACCESSORIES 29
- MODE D’EMPLOI 30
- DÉFINITIONS 31
- RÈGLES GÉNÉRALES DE SÉCURITÉ 31
- CONSERVER CES DIRECTIVES 33
- LES SCIES DE TABLE 33
- CONNEXIONS ÉLECTRIQUES 34
- DIRECTIVES DE MISE À LA TERRE 34
- SUPÉRIEURE À 50 PIEDS 35
- NON RECOMMANDÉE 35
- ASSEMBLAGE 36
- DÉSEMBALLAGE ET NETTOYAGE 36
- PIÈCES DU SOCLE 38
- AVERTISSEMENT 39
- ENSEMBLE DE PROTÈGE-LAME 40
- ET COUTEAU SÉPARATEUR 40
- RALLONGES 40
- GUIDE LONGITUDINAL 41
- GUIDE D’ONGLET 41
- APPUI ARRIÈRE 41
- DÉMARRAGE ET ARRÊT DE LA SCIE 41
- PROVOQUER DES BLESSURES 42
- D’ONGLET 43
- CHANGEMENT DE LA LAME 44
- TRONÇONNAGE 44
- SCIAGE EN LONG 45
- LONGITUDINAL 45
- FRAISE ACCESSOIRE À RAINURER 45
- ATTENTION 46
- GUIDE DE DÉPANNAGE 47
- ACCESSOIRES 49
- MANUAL DE INSTRUCCIONES 50
- NORMAS GENERALES DE SEGURIDAD 51
- SIERRAS DE MESA 53
- CONEXIONES ELÉCTRICAS 54
- ESPECIFICACIONES DEL MOTOR 54
- Amperios En Pies 55
- ENSAMBLAJE 56
- DESEMBALAJE Y LIMPIEZA 56
- PARTES DE LA BASE 58
- BASES DE EXTENSIÓN 60
- RIEL DE GUÍA A LA SIERRA 60
- GUÍA DE CORTE LONGITUDINAL 61
- CALIBRADOR DE INGLETE 61
- SOPORTE DE AVANCE DE SALIDA 61
- CAMBIO DE LA HOJA 63
- CORTE TRANSVERSAL 64
- CORTE LONGITUDINAL 64
- VARA DE EMPUJE 67
- ACCESORIOS 68
Produits connexes et manuels pour Scies à onglets Black & Decker FIRESTORM FS210LS
(60 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.392 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels