Black & Decker BDPS200 Manuel d'instructions télécharger pdf (Page 28)

28 • ENGLISH

The liquid being sprayed may need to be thinned (diluted)

before starting. When thin- ning, use the proper liquid

thinner recom- mended on the container by the material

manufacturer and the proper dilution rate.

Warning!: Do not use materials with a flashpoint higher

than 60°C (140°F) .

A 2- 3/4 quart mixing bucket is provided to use

when transferring spray material from the original

container into the bucket for thinning and

measuring purposes (Fig. E).

f If material needs thinning, add the appropriate liquid

thinning material recommended by the manufacturer

(Fig. E1).

f The quick clean fill cup has a measurement of 2.5

ozs. This can be used as a quick measurement when

thinning to 5% in the side fill canister.

f It is possible to spray latex paint with this unit,

howeer, the required thinning may exceed material

manufacturer’s recommendation. The operator should

consider the type of application and final location of

the project when spraying.

COMMONDILUTION RATES ON PAINT CAN

MANUFACTURERS

SUGGESTED

OUNCES PER GALLON

1/2 pint 8 ounces

5% 6-1/2 ounces

10% 13 ounces

PREPARATION TIPS

f With any spraying job you should always ensure that

you have properly prepared the surface to get the best

finish. That is, that all surfaces are free from dust,

dirt, rust and grease. Lightly pressure wash decks or

exterior surfaces and ensure that they are dry before

spraying.

f It is recommended that you mask all edges and other

areas and use drop cloths to protect your floors and

anything else in the spraying area that you wish to

remain untouched.

f Skin that forms on the top of paint can clog the

sprayer. Remove skin before mixing. Older material

may need to be strained with a funnel with a filter

attached or through hosiery to remove any impurities

that could clog system.

f Before starting have gloves, paper towels, rags etc.

available for unexpected spills.

FILLING THE CANISTER - (FIG. F)

f Check to make sure that the canister is completely

screwed onto the sprayer.

f Lay the sprayer on its side with the canister side lid

facing up.

f Unscrew the lid on the side of the canister.

f Pour the properly thinned and strained material to be

sprayed into the side fill canister (Fig. F).

Tip: Use the mixing bucket provided to pour

material from the original material container into

the side fill canister.

f Clean any residual liquid from the threads or sides of

the canister and sprayer.

f Starting the threads evenly, screw the lid completely

onto the side fill canister. Check the lid to make sure it

is threaded on squarely and completely before picking

up the sprayer.

FLOW CONTROL SETTINGS

FLOW CONTROL KNOB - (FIG. G)

The flow control knob regulates the amount of liquid that

can be sprayed.

f Select low (1), medium (5) or high (9) on the flow

control knob.

Tip: Always test the spray pattern on scrap cardboard

or similar material first. Begin with flow control

knob on the highest flow setting. Heavier, thicker

materials should be sprayed on the higher setting

closer to #9. Thinner materials should be sprayed on

the lower setting closer to #1.

OPERATION

ON / OFF TRIGGER - (FIG. H)

The sprayer is turned on and off by the trigger.

f To turn the sprayer on, squeeze the trigger.

f To turn the sprayer off, release the trigger.

Warning!: Risk of injury. Never point the sprayer at

any part of the body. Never pull the trigger while adjusting

the spray setting.

DEVELOPING THE PROPER

SPRAYING TECHNIQUE

f Practice spraying on a piece of scrap material such

as cardboard to test your spray pattern and become

familiar with the speed settings flow control features

of the sprayer.

f Ensure surface to be sprayed is free of dust, dirt, and

grease.

f Ensure spray area is clean and free of dust that could

be blown onto newly sprayed surfaces.

f Cover any areas not intended to be sprayed.

1 2 ... 23 24 25 26 27 28 29 30 31 32

Commentaires sur ces manuels

Pas de commentaire

Black & Decker BDPS200 Manuel d'instructions Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Pulvérisateur de peinture Black & Decker BDPS200