Black & Decker BDPS200 Manuel d'instructions télécharger pdf (Page 29)

ENGLISH • 29

f Always spray from a minimum of 1 inch (25mm) to a

maximum of 14 inches (355mm) (figure I). Optimal is

usually around 10 inches or use a paint stir stick as a

reference.

f A commonly used method for spraying a large surface

is the “crisscross” pattern. This is done by spraying in

horizontal strips and then crossing over these strips

with vertical strips.

f To get an even spray distribution, always keep your

arm at the same distance (Fig. I) from the surface you

are spraying and avoid moving your wrist (Fig. I1).

f Maintain smooth and consistent speed which will help

avoid inconsistencies. Begin spraying after the pass

has begun and release trigger before stopping the

pass.

f Avoid spraying too heavily in any one area. Several

lighter coats are better than one heavy coat which can

lead to running and dripping. Remember that the flow

control knob regulates the amount of liquid that can

be sprayed. Turning the flow knob counterclockwise

increases the flow of liquid. Turning the knob

clockwise decreases the flow of liquid. If runs or drips

do occur, have a dry paint brush on hand to smooth

them out.

Warning!: ELECTRIC SHOCK HAZARD. When

spraying overhead, never tip the sprayer more than

45 degrees. The material being sprayed could leak into the

motor housing.

Tip: If the atomizer valve is not seated properly, spray

material will leak from behind the spray nozzle. If

material is leaking, turn off and unplug sprayer from

power source immediately. Follow these steps to

correct the problem:

f Check that the sprayer is unplugged from the

power source. Remove the spray nozzle by turning

counterclockwise (Fig. J). For the fan nozzle,

remember to push and turn counter- clockwise to

remove.

f Remove the atomizer and check to see if it needs to

be cleaned or replaced. Also check inside the pump

housing for any debris or obstruction and clean if

necessary (Fig. J1).

f Replace the atomizer valve making sure it seats

properly (Fig. J2).

f Thread the spray nozzle back onto the sprayer by

turning clockwise (Fig. J3).

CLEANING

Warning!:Be sure to use appropriate protective gear.

f Make sure clean up area is well ventilated and free of

flammable vapors.

f Always spray outdoors when spraying cleaning

solution through sprayer.

f Use drop cloths during pouring, mixing, and viscosity

testing of materials to be sprayed to protect your

floors and anything else in the spraying area that you

wish to remain untouched.

TO BEGIN CLEANING:

f Unplug the sprayer from the power source.

f Unscrew the lid from the side of the canister and pour

any remaining liquid back into the original container

(Fig. K).

f Pour a small amount of the appropriate cleaning

solution into the canister (Fig. K1).

f Warm soapy water for water based materials

f Manufacturers recommended cleaning solution for oil

based materials

f Replace the lid on the canister securely and

vigorously shake the sprayer.

f Unscrew the lid from the side of the canister and

properly dispose of cleaning solution.

f Refill the canister with a small amount of new cleaning

solution (Fig. K1). Screw lid securely on canister.

f Plug in the cord and spray the cleaning solution

through the sprayer onto scrap material for 5 seconds

(Fig. K2).

f Unplug the sprayer from the power source.

f Properly dispose of cleaning solution.

f Remove the spray nozzle, by turning

counterclockwise, then remove the atomizer (Fig. K3).

Refer to Fig. C & C1.

f Unscrew the canister from the sprayer by turning the

collar as shown in Fig. K4.

f Remove the pickup tube and filter and o-ring from the

sprayer. Clean the parts with the cleaning brush in the

appropriate cleaning solution.

f Remove the front housing of the sprayer, by pressing

down on the release button and pulling the front

housing off of the sprayer (Fig. K5, K6).

f Remove the piston and spring (Fig. K7).

f Clean the spray nozzle, pickup tube and filter,

atomizer, piston and spring with the cleaning brush in

the appropriate cleaning solution (Fig. K8).

f Thoroughly clean the inside of the piston chamber

with the cleaning brush (Fig. K9).

Important: Be sure to remove all material from inside

of piston chamber. A small amount of material that is not

removed with the cleaning brush can harden over time and

interfere with the movement of the piston causing damage

to the sprayer.

1 2 ... 24 25 26 27 28 29 30 31 32

Commentaires sur ces manuels

Pas de commentaire

Black & Decker BDPS200 Manuel d'instructions Page 29

Commentaires sur ces manuels

Produits connexes et manuels pour Pulvérisateur de peinture Black & Decker BDPS200