Black & Decker Lithium-Ion Halogen Spotlight Manuel d'instructions télécharger pdf (Page 5)

3. Check fuse with a continuity checker.

4. If blown, locate a replacement 8 amp/250 volt fuse.

5. Replace the fuse, spring, contact and end cap.

 6.Screwendcapclockwiseuntilitisfingertight–DONOTOVER-TIGHTEN.

7. Test for proper operation of the 12 volt DC charging adapter.

TROUBLESHOOTING

Problem

Solution

The battery/charge status

LED indicator does not light

when charging

1. Check connection to the 12 Volt AC to DC Charging Port or the

12 Volt DC Power and Charging Port.

2. Check connection to AC or DC power source.

3. Confirm there is a functioning AC or DC current.

Unit will not operate in

corded mode

1. Check connection to the 12 Volt DC Power and Charging Port.

2. Check connection to the DC power source.

3. Confirm there is a functioning DC current.

4. Check that the fuse in the 12 Volt DC Adapter is not blown.

Unit will not operate

1. The battery may be completely discharged. Charge the unit

following the directions.

2. The halogen bulb may have blown. Check bulb filament. If the

filament is coiled and unbroken, the bulb is not blown. Otherwise,

replace the bulb following the instructions in the manual.

ONE-YEAR

LIMITED

WARRANTY

The manufacturer warrants this product against defects in materials and workmanship for a period

of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty

Period”).

If there is a defect and a valid claim is received within the Warranty Period, the defective product can

be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or

replacementatmanufacturer’soption.Proofofpurchasemayberequiredbymanufacturer.(2)Return

the product to the retailer where product was purchased for an exchange (provided that the store is a

participatingretailer).Returnstoretailershouldbemadewithinthetimeperiodoftheretailer’sreturn

policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required.

Please check with the retailer for their specific return policy regarding returns that are beyond the time

set for exchanges.

This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal

wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair;

neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.

This warranty gives you, the original retail purchaser, specific legal rights and you may have other

rights which vary from state to state or province to province. This product is not intended for

commercial use.

PHILLIPS SCREW

PHILLIPS

SCREW

RETAINING

SCREW

ON/OFF

TRIGGER

RUBBER BEZEL

Use a screwdriver to gently pry

the Rubber Bezel off.

RETAINING

RING

HALOGEN BULB ASSEMBLY

GLASS

LENS

RUBBER

"O" RING

LIGHT

REFLECTOR

HALOGEN BULB ASSEMBLY

Only replace the bulb in an integrated

assembly of lamp holder, wire and tab.

HAIRPIN

RETAINING

WIRE

LIGHT REFLECTOR

1. Disconnect the unit from any charging adapters.

2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws

in the retaining ring.

3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.

4. Lift off the retaining ring, glass lens and rubber “O” ring and set them aside.

5. Carefully remove the reflector and bulb assembly.

 6.Disconnectthebulbwirefromtheredpowerwire.

 7.Unsnapthehairpinretainingwiresfromthereflector’sflange.

8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need

to completely remove this screw).

9. Lift out the bulb and detach wire.

10.Insertthereplacementbulbintothereflector’sflange.

11. Put back and secure the hairpin retaining wires.

12. Connect the bulb power wire to the red power wire.

13. Tighten the retaining screw on the flange.

14. Place the reflector in position in the body of the spotlight.

15. Replace the glass lens rubber “O” ring in the groove around the perimeter of the reflector.

16.Replaceretainingringsothescrewholesarealigned.

17. Secure retaining ring with two screws.

18. Replace rubber bezel.

19. Operate switch to ensure proper operation of spotlight.

WARNING: To reduce the risk of electric shock, replace bulb with 9 volt, H3 40 watt only.

12 volt DC Adapter plug fuse replacement

Thefuseintheplugendofthe12VoltDCAdapterprotectstheadapter’schargingcircuit.Ifthe120Volt

AC Adapter operates, but the DC charging adapter does not, then this fuse may be opened (blown).

To replace the fuse:

1. Unscrew the end cap of the DC plug (counterclockwise).

2. Remove spring center contact and fuse.

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Black & Decker Lithium-Ion Halogen Spotlight Manuel d'instructions Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batterie Black & Decker Lithium-Ion Halogen Spotlight