Black & Decker FM1700 Manuel d'utilisateur télécharger pdf (Page 11)

ENGLISH • 11

b. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power

tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts and

any other condition that may affect the power

tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

5. Service

a. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

6. Electrical safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating

plate.

Warning! If the power cord is damaged, it must

be replaced by the manufacturer, authorized

Black & Decker Service Center or an equally

qualified person in order to avoid damage or

injury. If the power cord is replaced by an equally

qualified person, but not authorized by Black &

Decker, the warranty will not be valid.

7. Labels on tool

The label on your tool may include the following symbols:

FEATURES (Fig. A)

1. Wool bonnet

2. Flange nut

3. Rubber pad

4. Flange nut

5. Side handle

6. Trigger lock

7. Trigger

8. Cord guard

9. Speed level

10. Lock button

Installing the side handle

The side handle should always be used during operation.

Screw the handle into the top, left or right of the grinder

housing .It¢s determined by your need.

On/Off Switch

1. Pressing trigger (7) while moving trigger lock (6)

forward to turn “ON” the tool. And moving trigger lock

forward again, the trigger will locked.

2. Press trigger (7) again to turn the tool ”OFF”.

Mounting and dismounting the wool bonnet

1. Insert the washer nut through the rubber pad and

thread it onto the spindle.

2. While holding the spindle with the stop pin (10).

Turn the washer nut clock wise with accessory

wrench to screw it onto the spindle. Ensure that the

washer nut is thoroughly tightened by using wrench.

3. Wrap the rubber pad with the hood of the wool bonnet

and firmly secure it by tightening and trying its draw

string. Be surethe excess string is firmly rucked inside

the wool bonnet to prevent ittrom flying out while

polishing.

Caution! Improper fitting of the wool bonnet may

cause vibration.

4. To remove the wool bonnet follow the above

procedures in reverse.

APPLICATIONS

1. Polishing varnished surfaces of wooden furniture, etc.

2. Shining synthetic resin or ebonite products.

3. Fiber Glass polishing applications

4. Automotive polishing

Practical electric polisher appliactions

When utilizing this tool as a polisher, set the speed to a

lower speed for maximum efficiency.

1. Curved surfaces as well as flat surfaces can be

efficiently finished. Do not excessively push the

polisher against the surface of the material. The

weight of the polisher alone is sufficient for effective

polishing. Excessive pressure will result in a poor

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

1 2 ... 6 7 8 9 10 11 12 13

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FM1700 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker FM1700