Black & Decker VEC1093DBD Manuel d'utilisateur télécharger pdf (Page 7)

BATTERY RECONDITION MODE should only be used with 10 Amp Hour (Ah) or

larger capacity lead-acid batteries, Charge the battery to be treated for 20 minutes,

before using RECONDITION Mode. Observe the Digital Display tar any codes. This

initial charge will check the battery for shorted cells (F01), open cells (FO3) or battery

too low to accept a charge (FO2), and to ensure the battery carl take a charge. If

code (FO3) is displayed, change to the BATTERY RECONDITION MODE.

Remove or disconnect the vehicle's battery when reconditioning.

1, Make sure the charger is in initiation state with a circulating pattern on the

display or in charge OFF rhode with "OOO" on the display. If not, press

4/10/20/40 AMP button repeatedly until "OOO" shows on the display.

2. Press the Battely Recondition button to start the process,

3, DES appears on the display for 3 seconds, then it changes to three horizontal

moving bars.

4. The process takes 24 hauls and stops automatically. The display shows "O00"

when complete.

Alternator Voltage Check

Part 1

No Load

Part 2

(Turn OFF all vehicle's accessories): The battery must be fully charged

before testing the alternator. Run the engine long enough to achieve

normal idle speed and verify there is a no-load voltage,

1. Press Alternator Check to star[ the check.

2, Alternator Good LED will light to indicate the alternator is good, or F07

will display if alternator output voltage is out of typical operation range,

3, Press Alternator Check again to stop the test,

Under Load (Accessories ON): Next, load the alternator by turning on as many

accessories as possible (except for A/C and DEFROST)

1, Press Alternator Check to start the check.

2. Alternator Good LED will light to indicate the alternator is good, or F07

will display if alternator output voltage is out of typical operation range.

3, Press Alternator Check again to stop the test,

If the first alternator check indicates a good alternator and the second indicates the

alternatol is bad, the problem could stem from: loose fan belts, an intermittent diode

failure or possibly bad connections between tile battery and alternator and/or ground.

Notes: BATTERY VOLTAGE button is disabled in Alternator Check mode.

F07 may display because someor_ has added a number of accessory loads

on the charging system, thereby increasing current demand from the

alternator. MAKE SURE THAT THE ALTERNATOR IS RATED TO SUPPORT THE

APPLICATION.

This check may not be accurate for every make, manufacturer and model of

vehicle.

Check only 12 volt systems.

APPROXIMATE CHARGING TIMES

The 4/10/20/40 Amp 12 Volt Smart Battery Charger will automatically

adjust the charge rate as the battery becomes charged and stop when the battery is

fully charged, Deep cycle batteries may require longer charging time,

For estimates of the time it takes to charge a battery, refer to the following table.

Percent of charge

in battery

75% 50% 25%

at 4 Amp rate 3,5 HRS 7 HRS 10,5 HRS

at 10 amp rate !,4 HRS 2,8 HRB 4,2 HRS

at 20 Amp rate 1 HR 1,5 HRS 2,1 HRS

14 HRS

5,5 HRS

2,8 HRS

1-2 HRS

at 40 Amp rate 1 HR 1 HR _ 1 HR_

* Not recommendedfor charging batterieslessthan 80 Ah

The times shown irl the table above are approximate and refer to a BO All automotive

battery. For example, a 50 Ah (12 volt) battery is discharged (50%). How long

should it be charged at the 10 amp rate? See the chart above under "NO%" and "at

10 amp rate."

In ttlOSt cases, battery charging tittles will vary depending on the size, age and

condition of tile battery. Smaller batteries should be charged at a lower rate (4 amps)

and an extra hour added to chalge time,

CARE AND MAINTENANCE

With proper care and minimal maintenance, the 4/10/20/40 Amp 12 Volt

Smart Battery Charger will provide years of dependable service. Fo_ maximum

performance, manufacturer recommends:

* After each use, clean the battery charger clamps -- be sure to remove any battery

fluid that will cause corrosion of the clamps,

- Clean the outside case of the charger with a soft cloth and, if necessary, mild soap

solution,

• Do not allow liquid to enter the charger, Do not operate when charger is wet,

• Keep the charger cords loosely coiled during storage to prevent damage to the

cords,

WARNINGS

• Do not use charger if cords or clamps have been damaged in any

way -- cab Technical Support toll-free at (800) 618-5178.

,_There are no user-serviceable parts in this unit.

• Do not open the unit. in the event of malfunction, it must be returned

to manufacturer for professional testing and repair. OPENING THE

UNIT WiLL VOiD THE MANUFACTURER'S WARRANTY.

8 9

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

Black & Decker VEC1093DBD Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batteries pour voitures Black & Decker VEC1093DBD