Black & Decker VEC1093DBD Manuel d'utilisateur télécharger pdf (Page 3)

VECI093DBDManual 050205 5/5/05 6:32 PM Page iv

5 For negative-grounded vehicle, connect POSITIVE (RED) clamp from battery chargel to POSITIVE

(POS, P +) ungrounded pox of balter_ Connect NEGATIVE (BLACK) clamp _ vehicle chassis or

engine block away from batter_ Do rl_ connect clip to carburetor, fuel lines, or sheet-meal body

paris¸ Connect to heavy gauge metal part of the frame or engine block¸

6 For posifive-grou_/ded vehicle¸ connect NEGATIVE (BLACK) clamp from battery charger Io

NEGATIVE (NEG, N, ½ ungrounded pox of battery¸ Connect POSiTiVE (RED) clamp to vehicle

chassis or engine block away from battery¸ Do not connect clip to carburetor, fuel lines or sheet-

metal body parts¸ Connect to a heavy gauge metal part of the frame or engEne block¸

7 When disconnecting charger, disconnect AC cord, remove clamp from vehicle chassis¸ and then

remove clamp from battery terminal

8 Do not charge the battery while the el_gine is operating¸

9 See operating instructions for lenglh of charge information¸

FoRow _.hese steps when the battery has been removed from a vehicle. A spark near

the battery may cause an exptosion. To reduce risk of a spark near the battery:

1 Check polarity of battery po_s The POSiTiVE post (marked POS,E +) usually has a larger diameter

than the NEGATIVE battery po_ (marked NEG, N, )

2 Attach a 24-inch (minimum length) 6 AWG insulated battery cable to lhe NEGATIVE battery post

(marked NEG, N, )

3 Connect the POSiTiVE (RED) battery clamp Io the POSiTiVE baltery po_ (marked POS, P + or red)¸

4 Stand as far back from the battery as possibler and do n_ face battery when making final

connecliorL

6 Carefully conne_ the NEGATIVE (BLACK) charger clamp to tbe free end of the battery cable

connected to the NEGATIVE lerminal

6 Set the dlarge rate to appropriate setting according to battery size¸

7 Wben disconnecting charger, always do so in reverse sequence of connecting procedure and break

first connectfel/ while as far away from battery as practical¸

Note: A marine (boat) battery must be removed and charged on shore. To charge

on board requires equipment specfaRy designed _r marine use. This unft is

NOT designed for such use.

SAVE THESE |NSTRUCTiONS

This device complies witb part 15 of the FCC rules Operat[oll is subject Io lhe following two

conditions: (1) tbis device may not cause harmful interference, and (2) this device mu_ accept

any interference receivedr including i_erference that may cause undesired operation¸

This equipment bas been tested and found to comply with tbe limits for a Class B digital device,

pursuant to part 15 of the FCC Rules¸ These limits are designed to provide reasonable prolectiol/

again_ harmful inlerfer ence in a residel/fial il/slallation This equipmel/t generatesr uses and call

radiate radio frequel_cy energy andr if n_ in.ailed and used in accordance with tbe

in_ructions, may c_use h_rmful interfererlce to rEidio communications However, tbere is no

guara_ee that interference will n_ occur in a particular in_allation [f equipme_ does cause

harmfel interference to radio or television reception, which can be determined by turning _e

equipment off and Onr the user is encouraged to try to correct the interference by one or more

of the following measures:

* Reorient or refecate the receiving antenna¸

o increase tbe separation between equipment and receiver¸

* Connect the equipment into an outlet on a ci_uit different from that to which tbe receiver is

conneoted

• Consult the dealer or an expedenced radio/TV technician for help¸

IntloductJon

Features

_'oNJrols alJd J(]lca(ois

Operating NSTrUCT[ON_

Charge Rate Selection

Charging the Batter

Automatic Float Charglug

Equalizing

Enghe Staff

Recondition Mode

AItematoi Check

Approximate Chal #n rimes

Ca/e and Maiutenance

[roubleshooR j

iNTRODUCTiON

Thank you for selecting the 40/20/70/4 Amp Smart Battery Charger. With

proper care and use, it will give you years of dependable service, This battery

charger has a high charge rate of up to 40 amps, a low charge rate of 4 amps and

110 amps of engine starting power, It is designed for charging only

12 volt lead-acid batteries- conventional automotive, maintenance-free, marine

deep cycle and gel -- used in cars, trucks, farm equipment, boats, RVs and SUVs,

lawn mowers/garden tractors, motolcycles, personal watelcraft, snowmobiles, ATVs

and various applications.

Smart Battery Chargers feature g-stage high-efficiency charging technology built-in

microprocessor control that ensures fast, safe and complete charging of serviceable

batteries.

Charge Curve

STAGEONE

BEEP _ BEEP

CHARGING

COMPLETE

Stage One -- Rapid Start Charge at 40 amps delivers maxJrnum charging

amperage to "wake up" any serviceable 12 volt battery and allows fol quick engine

starting in just 1 minute (based on a midsize vehicle battery at 50% charge level),

Whet] battery reaches a maximum safe predetermined voltage, the charger will

automatically signal a "beep" and move into Stage 2 of the charging process.

1 2 3 4 5 6 7 8 9

Commentaires sur ces manuels

Pas de commentaire

Black & Decker VEC1093DBD Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batteries pour voitures Black & Decker VEC1093DBD