Black & Decker 395136-00 Manuel d'instructions télécharger pdf (Page 11)

If you have any questions, call 1-800-54-HOW-TO

clamped to your work support or moved to other job sites and

reclamped.

NOTE: If you elect to mount your saw to a piece of plywood, make

sure that the mounting screws don’t protrude from the bottom of the

wood. The plywood must sit flush on the work support. When

clamping the saw to any work surface, clamp only on the clamping

bosses where the mounting screw holes are located. Clamping at any

other point will interfere with the proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be sure the

mounting surface is not warped or otherwise uneven. If the saw rocks

on the surface, place a thin piece of material under one saw foot until

the saw sits firmly on the mounting surface.

Installing a New Saw Blade

(UNPLUG THE MITER SAW)

DO NOT USE FERROUS METAL OR MASONRY CUTTING

BLADES IN THIS SAW

With the saw arm in the upper position, raise the guard (2) as far as

possible. Loosen (but do not remove) the guard bracket screw, shown

in Figure 4 until the guard bracket can be raised enough to permit

access to the blade screw. Hold the guard up and depress the spindle

lock button (19) with one hand and use the supplied blade wrench in

the other hand to loosen (clockwise) the left hand threaded blade

screw.

NOTE: To use the spindle lock, depress the button as shown in

Figure 5 and rotate the blade by hand until you feel the lock engage.

Continue to hold the lock button in to keep the spindle from turning.

Remove the blade screw and the blade.

The inner clamp washer is installed first, then the blade and the outer

Familiarization

Place the saw on a smooth, flat surface such as a workbench or

strong table.

Examine Figures 1 & 2 and refer to the parts description to become

familiar with the saw and its various parts. The following section on

adjustments will refer to these terms and you must know what and

where the parts are. The part name is followed by the corresponding

part number Example - lock down pin (14).

Press down lightly on the operating handle and pull out the lock down

pin (14), as shown in Figure 3. Gently release the downward

pressure and allow the arm to rise to its full height. Use the lock down

pin when carrying the saw from one place to another. Use the

operating handle (1) to transport the saw or the hand indentations

(15) shown in Figure 2 after unplugging.

Specifications

CAPACITY OF CUT

47 degree miter left and right

47 degree bevel left: 2 degree right

0 degree miter - Max. Height 3-1/2 inches - Max. Width 5-1/2 inches

45 degree miter - Max. Height 3-1/2 inches - Max. Width 4-1/8 inches

45 degree bevel - Max. Height 2-1/2 inches - Max. Width 5-1/2 inches

Bench Mounting

Bench mounting holes (8) are provided in all four feet to facilitate

bench mounting, as shown in Figure 1. (Two different sized holes are

provided to accommodate different sizes of screws. Use either hole, it

is not necessary to use both.) Always mount your saw firmly to

prevent movement. To enhance the tool’s portability, it can be

mounted to a piece of 1/2" or thicker plywood which can then be

395136-00,03,BT1500 6/22/04 9:05 AM Page 11

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 395136-00 Manuel d'instructions Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker 395136-00