Black & Decker GTC610NM Manuel d'instructions télécharger pdf (Page 8)

ENGLISH

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains voltage

corresponds to the voltage on the rating plate.

Never attempt to replace the charger unit with a

regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Overview

1. Front handle switch

2. Trigger switch

3. Lock-off button

4. Ventilation slots

5. Guard

6. Battery

7. Blade sheath

Fig. A

8. Charger

9. Charging indicator

10. End of charge indicator

Assembly

Warning! Before assembly, remove the battery from the tool.

Fittingandremovingthebattery(g.B)

u To t the battery (6), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (11) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Chargingthebattery(g.A)

The battery needs to be charged before rst use and whenever

it fails to produce sufcient power on jobs that were easily

done before. When charging the battery for the rst time,

or after prolonged storage, it will only accept an 80% charge.

After several charge and discharge cycles, the battery will

attain full capacity. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

u To charge the battery (6), remove it from the tool and

insert it into the charger (8). The battery will only t into

the charger in one way. Do not force. Be sure that the

battery is fully seated in the charger.

u Plug in the charger.

8 hour charger

The battery will be fully charged in approx. 8 hours. It can be

removed at any time or left in the connected charger indenitely.

Switchingonandoff(g.C)

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently

and will only allow operation while holding the tool with both

hands.

Switching on

u Squeeze the front handle switch (1).

u Push the lock-off button (3) forward using your thumb and

at the same time squeeze the trigger switch (2).

u Release the lock-off button.

Switching off

u Release the front handle switch (1) or the trigger switch (2).

Warning! Never attempt to lock a switch in the on position.

Hints for optimum use

u Slightly tilt the tool (up to 15° relative to the line of cut) so

that the blade tips point slightly towards the hedge (g. D1).

This will cause the blades to cut more effectively.

u Start by trimming the top of the hedge. Hold the tool at the

desired angle and move it steadily along the line of cut

(g. D2). The double-sided blade allows you to cut in

either direction.

u In order to obtain a very straight cut, stretch a piece of

string along the length of the hedge at the desired height.

Use the string (12) as a guideline, cutting just above it

(g. D2).

u In order to obtain at sides, cut upwards with the growth

(g. D3). Younger stems move outwards when the blade

cuts downwards, causing shallow patches in the hedge.

u Take care to avoid any foreign objects. Especially avoid

hard objects such as metal wire and railings, as these

could damage the blades (g. D4).

u Regularly oil the blades.

u Consider purchasing a spare battery to extend the running

time of this tool. The catalogue number of the battery is

found in the technical data chart below.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GTC610NM Manuel d'instructions Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Taille-haie électrique Black & Decker GTC610NM