Black & Decker 300 AMP JUMP-STARTER/INFLATOR Spécifications télécharger pdf (Page 5)

required, fitting an appropriate nozzle to the air hose. An On/Off Switch located

on the back of the unit controls the power to the Inflator and the Pressure Gauge

light. Refer to the diagram on page 2 for locations of inflator hose and nozzle

storage hatch. Return hose to the storage compartment after use.

WARNINGS

• The inflator is capable of inflating up to 120 pounds per square inch

(psi) pressure. To avoid over-inflation, carefully follow instructions

on articles to be inflated. Never exceed recommended pressures.

Bursting articles can cause serious injury.

• Always check pressure with the pressure gauge.

• Never leave the inflator unattended while in use.

CAUTION

Do not operate inflator continuously for extended periods of time (approximately 15

minutes, depending on ambient temperatures), as it may overheat. In such event,

inflator will automatically shut down and restart after a cooling down period of

approximately 15 minutes.

Inflating Tires or Products With Valve Stems

1. Place connector (chuck) on valve stem.

2. Ensure connector is pushed on to valve stem as far as possible before closing

thumb latch.

3. Make sure latch is secure.

4. Turn ON the Inflator Power Switch.

5. Check pressure with the pressure gauge.

6. When desired pressure is reached, open thumb latch and remove connector

from valve stem.

7. Turn OFF Inflator Power Switch.

8. Allow unit to cool before storing away.

9. Store inflator hose and tire fitting in storage compartment.

Inflating Other Inflatables Without Valve Stems

Inflation of other items requires use of one of the adapters (nozzles).

1. Select the appropriate nozzle, located in the storage compartment on the back

of the unit.

2. Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb

latch.

3. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.

4. Turn ON the Inflator Power Switch — inflate to desired pressure or fullness.

5. Switch the Inflator Power Switch OFF.

6. Remove adapter.

7. Recharge the unit before storing away.

CARE AND MAINTENANCE

This product has a sealed lead acid battery that should be kept fully charged.

Recharge before first use, immediately after each use, and every 60 days if not

used. Failure to do this may reduce battery life dramatically.

discontinue jump-start procedure and look for other problems that

need to be corrected.

• After use, turn the Jump-Starter Power Switch OFF.

• Replace worn or defective parts immediately — contact the Customer

Service Department toll free (800) 618-5178.

CAUTIONS

• If the audible Reverse Connection Polarity Alarm sounds after clamps are

connected to vehicle battery, turn the unit OFF and reverse clamp connections

before continuing.

• If vehicle fails to start, turn OFF the ignition, turn OFF the Jump-Starter Power

Switch, disconnect the jump-start system’s leads and investigate why the engine

did not start.

• Recharge this unit fully after each use.

USING THE ALTERNATOR CHECK FEATURE

1. Make sure the Jump-Starter Power Switch is turned to OFF.

2. Remove jumper clamps from clamp tabs and connect to vehicle (refer to the

“Using the Jump-Starter” section for notes about polarity).

3. Start the engine.

4. Turn all vehicle accessories OFF.

5. Turn the Jump-Starter Power Switch to ON.

6. Observe the Alternator Check Indicator. A solid green LED indicates a good

alternator. A solid red LED indicates a bad alternator.

USING THE 12 VOLT DC PORTABLE POWER SUPPLY

This portable power source is also for use with all 12 volt DC accessories equipped

with a male accessory outlet plug that are rated up to 5 amps.

1. Lift up the cover of the unit‘s 12 Volt DC Accessory Outlet.

2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet

on the unit.

3. Switch on the appliance and operate as usual.

4. Periodically press the Battery Charge Level Pushbutton to check battery status.

CAUTION

Make sure the Jump-Starter Power Switch is ALWAYS in the OFF position when using

the unit’s 12 Volt DC Accessory Outlet.

DO NOT operate appliances that draw more than 5 amps.

USING THE PORTABLE INFLATOR

The built-in 12 volt DC inflator is the ultimate inflator for all vehicle tires, trailer tires

and recreational inflatables. Three different sized nozzles are supplied. Each nozzle

will clip on the end of the standard tire valve connector located at the free end of

the inflator hose. The inflator nozzles are stored inside the hose hatch. The inflator

hose with tire fitting is stored in a retaining channel between the jumper cable

channels on the rear of the unit. The inflator can operate long enough to fill up to

3 average sized tires before the battery must be recharged.

The inflator may be used by removing the air hose from the storage hatch and if

VEC1031CBD_ManualEN_032906 7/7/06 9:42 AM Page 4

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 300 AMP JUMP-STARTER/INFLATOR Spécifications Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Chargeurs de batteries pour voitures Black & Decker 300 AMP JUMP-STARTER/INFLATOR