Black & Decker Quantum Pro 629634-00 Manuel d'instructions télécharger pdf (Page 2)

MAINTENANCE

UNPLUG SAW AND REMOVE ACCESSORY WHEN PERFORMING ANY CLEANING OR

OTHER MAINTENANCE. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT

PARTS.

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to vari-

ous types of commercial solvents and may be damaged by their use. Use clean cloths to

remove dirt, carbon dust etc.

• When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are sub-

ject to accelerated wear and possible premature failure, as the fiberglass chips and

grindings and drywall dust are highly abrasive to bearings, brushes, commutator, etc.

During any use on fiberglass or drywall it is extremely important that the tool be cleaned

frequently by blowing with an air jet.

LUBRICATION

Your saw was properly lubricated before leaving the factory. Once every year take or send

your saw to a Black & Decker service center, or authorized service station, for a complete

cleaning, inspection and lubrication. Tools "out of service" for long periods should be

relubricated before being put back to work.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service

personnel, always using identical replacement parts

ACCESSORIES

BLADES

The QP5000 and QP5002 Reciprocating Saws will accept up to a 12 inch long blade.

Always use the shortest blade suitable for your project but long enough to keep the blade

cutting through the material. Longer blades are more likely to be bent or damaged during

use. During operation some longer blades may vibrate or shake if the saw is not kept in

contact with the workpiece.

PRUNING ATTACHMENT

A pruning attachment is also available for use with your QP5000 and QP5002

Reciprocating Saw. This accessory attaches to the shoe of the saw and applies spring

loaded pressure to the branch while cutting.

Recommended accessories for use with your saw are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service. Whether you

need technical advice, repair, or genuine factory replacement parts, contact the

Black & Decker location nearest you. To find your local service location, refer to the yellow

page directory under "Tools—Electric" or call: 1-800-544-6986.

FULL TWO YEAR WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge in

either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom

it was purchased (provided that the store is a participating retailer). Returns should be made

within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the

sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory and available on our website

www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center.

Free warning label replacement: If your warning labels become illegible or are missing,

call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Règles de sécurité générales

AVERTISSEMENT : S'assurer de lire et de comprendre toutes les directives. Ne

pas suivre les directives figurant ci-après peut causer un choc électrique, un incendie et

des blessures corporelles graves.

CONSERVER CES DIRECTIVES

Espace de travail

• Tenir l’espace de travail propre et bien éclairé. Les bancs de scie encombrés et les

endroits sombres sont souvent des causes d'accidents.

• Ne pas faire fonctionner d’outils électriques dans une atmosphère inflammable, soit

en présence de liquides inflammables, de gaz ou de poussière. Les outils électriques

produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs. Ne les

utiliser que dans les endroits bien aérés.

• Éloigner les curieux, les enfants et les visiteurs au moment d’utiliser un outil

électrique. Une distraction pourrait vous en faire perdre la maîtrise.

Sécurité en matière d'électricité

• Les outils à double isolation sont dotés d’une fiche polarisée (une lame de contact

est plus large que l’autre). Cette fiche ne se branche que d’une seule façon dans une

prise de courant polarisée. Si la fiche ne s’insère pas totalement dans la prise de

courant, l’inverser. Si elle ne s’insère toujours pas dans la prise, demander à un

électricien compétent d’installer une fiche polarisée. Ne pas remplacer la fiche. La

double isolation élimine la nécessité d’utiliser un cordon d’alimentation muni d’une fiche

à trois fils avec mise à la terre et un bloc d’alimentation avec mise à la terre.

• Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des cuisinières ou des réfrigérateurs. Le risque de choc électrique est plus élevé

lorsque votre corps est mis à la terre.

• Ne pas exposer ses outils électriques à la pluie ou à un environnement humide. La

pénétration de l’eau dans un outil électrique augmente le risque de choc électrique.

• Ne pas utiliser abusivement le cordon d’alimentation. Ne pas utiliser le cordon

d’alimentation pour transporter l’outil ni tirer dessus pour le débrancher de la prise

de courant. Tenir le cordon éloigné de la chaleur, de l’huile, des bords tranchants ou

des pièces mobiles. Remplacer immédiatement tout cordon endommagé. Un cordon

endommagé augmente le risque de choc électrique.

• Lorsqu’un outil électrique est utilisé à l’extérieur, utiliser une rallonge pour

l’extérieur portant la mention « W-A » ou « W ». Ces rallonges sont classées pour un

usage extérieur, ce qui réduit le risque de choc électrique.

Sécurité personnelle

• Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil

électrique est utilisé. Ne pas utiliser d'outil en cas de fatigue ou de prise de drogue,

d’alcool ou de médicaments. Un moment d’inattention, durant l’utilisation d’un outil

électrique, peut se solder par des blessures graves.

• S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Attacher les cheveux longs. Garder les cheveux, les vêtements et les gants à l'écart

des pièces mobiles. Les vêtements amples, bijoux ou cheveux longs pourraient

s'enchevêtrer dans les pièces mobiles. Se tenir à l'écart des évents, car ils couvrent des

pièces mobiles.

• Attention de ne pas mettre en marche l’outil accidentellement. S’assurer que

l’interrupteur est en position d’arrêt avant de brancher l’outil. Transporter un outil en

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size

extension cords with the tool – that is, proper wire size for various lengths of cord and heavy

enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. For proper size cords see chart

below.

MOTOR

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your

tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A

rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC

power. This information is printed on the nameplate. Lower voltage will cause loss of power

and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does

not operate, check the power supply.

SAVE THESE INSTRUCTIONS

OPERATION

CAUTION: Always wear eye protection while operating this power tool.

NOTE: Before cutting any type of material, be sure it is firmly anchored or clamped to pre-

vent slipping.

• Place blade lightly against work to be cut.

• Switch on saw motor before applying pressure.

• WARNING: LACERATION HAZARD. Never hold and use the product with your

fingers wrapped around shoe adjustment button. Always hold saw firmly with both

hands while cutting as shown in Figure 1. Whenever possible, the saw shoe must be

held firmly against the material being cut. This will prevent the saw from jumping or

vibrating and minimize blade breakage.

SWITCH (ON-OFF) (FIGURE 2)

Depress the trigger switch to turn tool “ON”. Releasing the trigger turns the tool “OFF”

NOTE: This tool has no provision to lock the switch in the ON position, and should never

be locked in the ON position by any other means.

VARIABLE SPEED SELECTOR WHEEL (FIGURE 3)

The variable speed selector wheel offers a choice of speeds for greatly improved cutting

rates in various materials. To select a slower speed for operating the saw, rotate the wheel

to a low number on the dial. To select a higher speed, rotate the wheel to a higher number.

TWO-SPEED (DUAL RANGE) SWITCH (FIGURE 3A) QP5002 ONLY

The 2-speed selector offers a choice of speeds for greatly improved cutting rates in various

materials. Note that the High-Speed setting is more efficient in softer materials such as

wood, while the Low-Speed is best for cutting metals.

LOW SPEED (Move slide switch to show 1). For cutting sheet metal, metal pipe, metal

conduit, etc.

HIGH SPEED (Move slide switch to show 2). For cutting wood, plastic, composition boards

and other similar materials.

BLADE CLAMP RELEASE LEVER (FIGURE 4)

CAUTION: TURN OFF AND UNPLUG FROM POWER SUPPLY WHEN CHANGING

BLADES.

To install blade into saw:

1. Lift the blade clamp release lever to its full open position as shown in Figure 4.

2. Insert blade shank from the front locating hole in blade over pin on reciprocating shaft.

3. Close blade clamp release lever.

4. Check to ensure blade is secure before cutting.

To remove blade from saw:

1. Open blade clamp release lever to its full open position.

2. Remove blade.

ADJUSTABLE SHOE (FIGURE 5)

CAUTION: TURN OFF AND UNPLUG SAW.

The shoe will adjust to limit the depth of cut. Hold the saw with the underside facing up.

Push the button (shown in Figure 5) on the hand grip and slide the shoe out to one of the

three settings and release the button.

FLUSH CUTTING (FIGURE 6)

• The compact design of the reciprocating saw motor housing and pivoting shoe permit

close cutting to floors, corners and other difficult areas.

• To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with

the teeth of the blade facing up.

• Turn the saw upside down so you are as close to the work surface as possible.

METAL CUTTING (FIGURE 7)

• Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials.

• In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will

ensure a clean cut without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage.

NOTE: Spread a thin film of oil or other coolant along the line ahead of the saw cut for

easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

POCKET CUTTING - WOOD ONLY (FIGURE 8)

• Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber.

• Insert blade in blade clamp and tighten blade clamp securely.

• Tip the saw backward until the back edge of the shoe is resting on the work surface and

the moving blade will clear the surface.

• Switch motor on, permitting blade to obtain maximum speed.

• Grip handle steadily and begin a slow, deliberate upward swing with the handle of the

saw.

• The blade will begin to feed into material. Always be sure blade is completely through

material before continuing with pocket cut.

NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide.

PROJECT TIPS

• Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor

while cutting.

• When cutting, always ensure that the shoe is resting firmly against the workpiece. This

will improve operator control and minimize vibration.

• For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to

high speed steel teeth making the blade more flexible and less prone to breaking.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUI SOIT, VEUILLEZ APPELER AU

1-800-54-HOW-TO (544-6986)

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Black & Decker Quantum Pro 629634-00 Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker Quantum Pro 629634-00