Black & Decker MT250 Manuel d'instructions télécharger pdf (Page 7)

ENGLISH

(Original instructions)

Carbide grout removal blade.

(Part number - X26125-XJ)

Carbide coated surface ideal for

clearing grout and tile adhesive from

at surfaces and for fast stock

removal of wood, chipboard and

breglass.

Carbide rasp.

(Part number - X26130-XJ)

Carbide coated surface ideal for grout

removal and for fast stock removal of

plastics, chipboard and breglass.

Sanding Sheets.

Various grades for sanding of wood,

painted and varnished surfaces.

Assembly

Fitting and removing the accessories (g. A - F)

Warning! Before tting an accessory, disconnect the tool from

the mains supply.

Fitting a Black & Decker / Piranha accessory (g. A - C)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Slide the accessory (8) between the shaft and the acces-

sory holder making sure the accessory engages all eight

pins on the holder and is ush with the shaft.

u Release the accessory clamping lever.

Note: Some accessories, such as scrapers and blades can be

mounted at an angle if required (g. C).

Removing a Black & Decker / Piranha accessory

accessory (g. A)

u Hold the tool and squeeze the accessory clamping lever

(3).

u Pull the accessory from the tool making sure the acces-

sory dis-engages from all eight pins on the holder.

u Release the accessory clamping lever.

Warning: Gloves must be worn when removing accessories

as they may become hot during use.

Fitting a sanding sheet (g. D)

u Line up the sanding sheet (9) with the sanding base (4) as

shown.

u Press the sheet rmly and evenly onto the sanding base,

making sure that the holes in the sheet coincide with the

holes in the base.

Removing a sanding sheet

u Pull the sanding sheet off the sanding base (4).

Warning! Never use the sanding base without a sanding

sheet or accessory in place.

Fitting the dust extraction adaptor (g. E)

u Line up the dust extraction adaptor (5) with the sanding

base (4) as shown.

u Press the adaptor rmly and evenly in to the sanding

base.

u Secure the adaptor by turning the locking nut (12) clock-

wise.

u Connect a vacuum cleaner to the dust extraction adaptor.

Removing the dust extraction adaptor

u Turn the locking nut (12) anti-clockwise.

u Pull the dust extraction adaptor (5) out of the sanding

base (4).

Fitting alternative accessories (g. F)

u Place the spacer (6) onto the collar (10).

u Place the alternative accessory (11) onto the collar (10).

u Firmly attach the xing bolt (7) into place to ensure a tight

t for the alternative accessory (11).

Note: The spacer and xing bolt are not used to attach Black

& Decker accessories. Black and decker accessories are

attached using the Super-lok

Tool free accessory clamping

lever.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before cutting into walls, oors or ceilings, check for

the location of wiring and pipes.

Variable speed control (g. G)

The variable speed control allows you to adapt the speed of

the tool to the application.

u Set the variable speed dial (2) to the desired setting. At

setting 1 the tool will operate at low speed, 10,000 min-1.

At setting 6 the tool will operate at the maximum speed,

20,000 min-1.

1 2 3 4 5 6 7 8 9 10 11 12 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Black & Decker MT250 Manuel d'instructions Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker MT250