6
Electrical safety
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Dustbag
3. Dust extraction outlet
4. Sanding base
5. Paper clamp lever
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting sanding sheets (fig. A & B)
Warning! Never use the tool without a sanding sheet or
accessory in place.
Fitting sanding sheets with nylon loops (fig. A)
Warning! Make sure that the tool is switched off and
unplugged.
Press the sheet firmly and evenly onto the sanding
base (4), making sure that the holes in the sheet line up
with the holes in the base.
Fitting regular sanding sheets (fig. B)
Warning! Make sure that the tool is switched off and
unplugged.
Soften the sanding sheet by rubbing its non-abrasive
side over the edge of a worktop.
Press the paper clamp levers (5) upwards to release
them from the retaining grooves and open the paper
clamps (5) by pressing them down.
Place the sheet onto the sanding base (4).
Insert the edge of the sanding sheet into the front paper
clamp (5) as shown.
Press the front paper clamp lever (5) downwards and
locate it in the retaining groove.
While keeping a slight tension on the sheet, insert the
rear edge of the sheet into the rear paper clamp (5).
Press the rear paper clamp lever (5) downwards and
locate it in the retaining groove.
Louvre attachment (fig. C) (KA400L only)
With this attachment you can work in crevices and use the
sanding base on both sides.
Locate the front of the louvre attachment (7) onto the
sanding base (4).
Secure it in position with the four screws supplied.
Place a 1/2 sheet to the underside of the louvre base.
Part of it will fold over the front part of the base.
To remove the louvre attachment (7), reverse the
procedure.
Fitting and removing the dustbag (fig. D)
Fit the dustbag (2) over the dust extraction outlet (3).
Slide the dustbag (2) onto the tool and make sure that it
is securely located.
To remove the dustbag (2), pull it to the rear and off the
outlet.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off (fig. E)
To switch the tool on, press the part of the on/off switch
(1) marked 'I'.
To switch the tool off, press the part of the on/off switch
(1) marked '0'.
Emptying the dustbag
The dustbag (2) should be emptied every 10 minutes.
Shake the dustbag (2) to empty the contents
Hints for optimum use
Do not place your hands over the ventilation slots.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding sheet.
Replace when necessary.
Always sand with the grain of the wood.
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
(16 pages)
(28 pages)
(78 pages)
(20 pages)
(16 pages)
(16 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels