Black & Decker 490525-00 Manuel d'instructions télécharger pdf (Page 2)

Motor

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means

your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC.

A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC

power. This information is printed on the nameplate. Lower voltage will cause loss of power

and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does

not operate, check the power supply.

SAVE THESE INSTRUCTIONS

Assembly

WARNING: Sharp blade. To prevent accidental operation, turn off and unplug saw

before performing the following operations. Failure to do this could result in serious

personal injury.

Fitting the saw blade (fig. A)

- Hold the saw blade (7) as shown, with teeth facing forward.

- Push the lever (4) downwards.

- Insert the shank of the saw blade into the blade holder (15) as far as it will go.

- Release the lever.

- Adjust the blade support roller as described below.

AccuCut

blade support roller (fig. B)

After fitting the blade, you need to adjust the blade support roller (5).

Screwdriver Method

- Turn the slotted blade support adjustment screw (6) in direction A.

- Slide the blade support roller against the rear of the blade. The blade must locate

in the central recess of the roller.

- Turn the blade support adjustment screw in direction B to lock the blade support in place.

Tool Free Method

- The blade support roller can be adjusted in a “tool free” manner, by turning the scrolling

knob (8) so that the adjustment screw is rotated around to the front of the unit where it can

be turned by hand.

Connecting a vacuum cleaner to the tool (fig. C & D)

- Align the dust extraction adaptor (14) with the saw shoe as shown.

- Insert the ribs (16) into the slots (17).

- Pull the adaptor towards the rear of the jigsaw to secure.

- Connect the vacuum cleaner hose (18) (not supplied) to the adaptor.

- Dust extraction is not possible when making bevel cuts.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal

filings will be hot and could cause a fire in the vacuum container.

Operating the Jig Saw

WARNING: Laceration Hazard. To prevent loss of control, never use the tool when

the saw shoe is loose or removed. Failure to do this could result in serious personal injury.

Adjusting the shoe plate for bevel cuts (fig. E)

The shoe plate can be set to a left or right bevel angle of up to 45°.

- Turn the locking knob (11) in direction A to release the shoe plate (10).

- Pull the shoe plate (10) backwards and set it to the required angle. You can use the

scale or a protractor to check the angle.

- Turn the locking knob (11) in direction B to lock the shoe plate in place.

To reset the shoe plate for straight cuts:

- Turn the locking knob (11) in direction A to release the shoe plate (10).

- Pull the shoe plate backwards and set it to an angle of approximately 0.

- Push the shoe plate forward.

- Turn the locking knob (11) in direction B to lock the shoe plate in place. Make sure that

the shoe plate is supported by the guide ribs.

Variable speed control

- Set the variable speed control knob (3) to the required speed range. Use a high speed

for wood, medium speed for aluminum and PVC and low speed for metals other than

aluminum.

Switching On and Off

- To switch the tool on, press the on/off switch (1).

- For continuous operation, press the lock-on button (2) and release the on/off switch.

- To switch the tool off, release the on/off switch. To switch the tool off, when in continuous

operation, press the on/off switch once more and release it.

Using the mode selector

The mode selector (9) can set in 3 positions

1. Scrolling position (figs F and G) - this position allows the scroller knob (8) to be

rotated for intricate and accurate sawing. (In this position there is no orbital action.)

It is recommended to use scroller blades when in this mode.

2. Straight cutting position (figs Ha, Hb and Hc ) this position turns off orbital action and

locks the scroller knob to prevent its rotation. The scroller knob can be locked in any

of 4 positions for straight cutting.

Method of engagement:

a. Turn the Mode Selector to the scrolling position.

b. Rotate the scroller knob to the desired position (this can be any of 4 positions -

the blade can point forwards, reverse, left or right).

c. Turn the Mode Selector to the neutral position. (In this position the Scroller Knob

cannot be turned).

3. Orbital Action Position (figs Ia, Ib and Ic) - this position switches on the orbital action

for fast and efficient straight cuts. This mode can only be selected with the blade

pointing forwards.

Method of engagement:

a. Turn the mode selector to the scrolling position.

b. Rotate the scroller knob to point the blade forwards.

c. Turn the Mode Selector to the orbital position. (In this position the Scroller Knob

cannot be turned).

Operating the Laser

Installing the batteries

Detach the laser from the jig saw by removing the screw shown in figure J and pulling laser

forward. Insert 2 fresh 1.5 volt AAA alkaline batteries making sure to match (+) and (-)

terminals correctly. Reattach the laser.

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this

risk:

• Carefully follow all instructions and warnings on the battery label and package. • Always

insert batteries correctly with regard to polarity (+ and -), marked on the battery and the

equipment. • Do not short battery terminals. • Do not charge batteries. • Do not mix old

and new batteries. Replace all of them at the same time with new batteries of the same

brand and type. • Remove dead batteries immediately and dispose of per local codes. •

Do not dispose of batteries in fire. • Keep batteries out of reach of children. • Remove bat-

teries if the device will not be used for several months.

max

COMPLIES

WITH 21CFR

PARTS 1040.10 AND

1040.11 EXCEPT FOR

DEVIATIONS PURSUANT

TO LASER NOTICE NO.50,

DATED JULY 26,2001.

588808-01 Made in China

Type 1 3V DC

Use with compatible

B&D Jig Saws.

Pats. Pend.

1-800-54-HOW-TO

Black & Decker (U.S.) Inc.,

Towson, MD 21286 U.S.A.

LISTED

406A

WARNING/ADVERTENCIA/AVERTISSEMENT

To reduce the risk of injury,

user must read and

understand instruction

manual. Use (2) AAA

size alkaline batteries.

À titre préventif,

lire le guide.

Para reducir el riesgo de

lesiones, el usuario debe

leer y entender el

manual de

instrucciones.

Utilice (2) baterías

alcalinas AAA.

ON/OFF

For your convenience and safety, the following labels are on the laser.

Pour plus de commodité et de sécurité, les étiquettes suivantes sont apposées sur le laser.

Para su comodidad y seguridad, el láser incluye las siguientes etiquetas.

Laser On/Off Button

Bouton marche/arrêt du laser

Botón de encendido/apagado del láser

Screw

Vis

Tornillo

OFF

1 2 3 4 5 6 7

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 490525-00 Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Black & Decker 490525-00