Black & Decker FV1205N Manuel d'instructions télécharger pdf (Page 6)

Features

1. Pivot lock trigger

2. Dust container door

3. Release latch (for dust container door)

4. Charging base

5. Charging indicator

6. Pivoting arm

7. Beater bar/vac head

8. Maintenance access panel

9. Beater bar/vac On/Off switch

Installation

Attaching the handle to the appliance (fig. A)

X Align the D-handle with the main body of the unit and

push it down until it is fully seated.

X Remove the phillips head screw from the plastic bag.

X Insert the screw (13) into the hole.

X Tighten the screw (13) using a phillips screwdriver.

Charging base (fig. B)

Place the charging base (4) on the floor, convenient to an

electrical outlet. The Pivot Plus

slim vac is stored and

charged in the base whenever it is not in use.

Warning! Falling/tripping hazard. Do not place the charging

base on any elevated surface. The appliance is designed to

be placed into and removed from the charging base when it

is sitting on the floor convenient to an electrical outlet.

Use

Before first use, the battery must be charged for at least 16

hours.

X Place the appliance on the charging base (4) whenever

it is not in use.

You may need to charge the appliance many times initially in

order to achieve the best running time performance.

Charging the battery (fig. B)

Warning! Do not charge the battery at ambient

temperatures below 10°C or above 40°C.

X Make sure that the appliance is switched off.

The battery will not be charged with the beater bar/vac on/off

switch (9) in the on position.

X Place the appliance on the charging base (4) as shown.

X Plug in the charger. Switch on at the mains.

The charging indicator (5) will be lit.

X For the first charging, leave the appliance to charge for

at least 16 hours.

While charging, the charger may become warm. This is

normal and does not indicate a problem.

The appliance can be left connected to the charger

indefinitely. The charging indicator (5) will be lit as long as

the appliance is connected to the plugged-in charger.

Opening the appliance (fig B, C and D)

X To open the appliance for use, lift it from the charging

base (4) (fig. B).

X Pull back the pivot lock trigger (1) on the handle and

rotate the vacuum head (fig. C).

X Release the pivot lock trigger (1) to lock the appliance in

any of the three different working positions a, b and c

(fig. D).

Switching on and off (fig. E)

X To switch the appliance on, slide the beater bar/vac On/

Off switch (9) forward to position 1 (vacuum only).

X For vacuuming with the beater bar operation, slide the

switch (9) forward to position 2.

X To switch the appliance off, slide the switch (9) back to

position 0.

Troubleshooting

If the product does not work, check the following:

X The charger was correctly plugged in for recharge (it

feels slightly warm to the touch).

X The charger cord is not damaged and is correctly

attached to the base.

X The charger is plugged into a working electrical outlet.

If the unit does not charge, check the following:

X Make sure that the beater bar/vac On/Off switch (9) is at

position 0. The appliance will not charge if the appliance

is switched ON.

Cleaning and maintenance

Warning! Regularly clean the filters.

Cleaning the dust container and filters (fig. F and G)

The filters are re-usable and should be cleaned regularly.

X Press the release latch (3) and open the container

door (2).

X Remove the filters (10 and 11).

X Empty the dust container.

X Brush any loose dust off the filters.

X Wash the filters in warm, soapy water (fig. G).

Warning! Do not immerse the appliance in water. A damp

cloth and soapy water should be used to clean the exterior

of the appliance. Always make sure that the appliance is

completely dry before re-use or storing.

X Make sure that the filters (10 and 11) are dry.

X Refit the filters (10 and 11).

X Close the container door (2). Make sure that the release

latch (3) clicks into place.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FV1205N Manuel d'instructions Page 6

Commentaires sur ces manuels