Black & Decker HX210-QS Manuel d'instructions télécharger pdf (Page 8)

ENGLISH

(Original instructions)

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. G)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u To charge the battery (4), insert it into the charger (20).

The battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (19) will ash green continuously

(slowly).

The charge is complete when the charging indicator (19) lights

green continuously. The charger and the battery can be left

connected indenitely with the LED illuminated. The LED will

change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging

indicator (19) will be lit as long as the battery is connected to

the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (19) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (4).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

State of charge indicator (g. H)

The battery is tted with a state of charge indicator. This can

be used to display the current level of charge in the battery

during use and during charging.

u Press the state of charge indicator button (21).

Setting the tool to trimming or edging mode (g. I

- K)

The tool can be used in trimming mode as shown in g. I or in

edging mode to trim overhanging grass along lawn edges and

ower beds as shown in g. J.

Trimming mode (g. I & K)

For trimming, the trimmer head should be in the position

shown in g. I. If it is not:

u Remove the battery from the tool.

u Press and hold the head release button (23).

u Whilst holding the handle, rotate the head (8) clockwise.

u Release the head release button (23).

u Lift the edge guide (9) into the closed position.

Note: Note: The head will only rotate in one direction.

Edging mode (g. J & K)

For edging, the trimmer head should be in the position shown

in g. J. If it is not:

u Remove the battery from the tool.

u Press and hold the head release button (23).

u Whilst holding the handle, rotate the head (8) anti-

clockwise.

u Release the head release button (23).

u Drop the edge guide in to the open position. Ensure that

the edging guide (9) is all the way down, an audible click

will be heard.

Note: The head will only rotate in one direction.

Switching on and off (g. L)

u To switch the tool on, press in and hold the lock off button

(3) then squeeze the trigger lever (1). Once the tool is

running you may release the lock off button (3).

u To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on

position.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker HX210-QS Manuel d'instructions Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Tondeuses à gazon Black & Decker HX210-QS