Black & Decker GLC2500L Manuel d'instructions télécharger pdf (Page 10)

ENGLISH

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

u After use disconnect the battery and check the tool for any

damage.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly clean the cutting line and spool using a soft

brush or dry cloth.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Storage

When the tool will not be used for several months, ideally

leave the battery connected to the charger. Otherwise proceed

as follows:

u Fully charge the battery.

u Remove the battery from the tool.

u Store the tool and battery in a secure and dry location.

The storage temperature must always remain in the range

of +5 °C to +40 °C. Place the battery on a level surface.

u Before using the tool after prolonged storage, fully charge

the battery again.

Troubleshooting

If your tool seems not to operate properly, follow the instructions

below. If this does not solve the problem, please contact your

local Black & Decker repair agent.

Warning! Before proceeding, remove the battery from the tool.

Tool runs slowly

u Check that the spool housing can rotate freely.

Carefully clean it if necessary.

u Check that the cutting line does not protrude more than

10-12 cm from the spool housing. If it does, cut it off so

that it just reaches the line trimming blade.

Automatic line feed does not work

u Keep the tabs depressed and remove the spool cover

from the housing.

u Lift the spool approx. 6 mm and pull the cutting line until it

protrudes 10-12 cm from the housing. If insufcient cutting

line is left on the spool, install a new spool of cutting line

as instructed above.

u Push the spool back into place and rotate it slightly until it

is seated.

u Align the tabs on the spool cover with the holes in the

housing.

u Push the cover onto the housing until it snaps securely

into place.

u If the cutting line protrudes beyond the trimming blade,

cut it off so that it just reaches the blade.

If the automatic line feed still does not work, try the following

suggestions:

u Carefully clean the spool housing.

u Remove the spool and check if the lever can move freely.

u Remove the spool and unwind the cutting line, then wind it

on neatly again as described above. Replace the spool as

instructed.

Spool is jammed

u Keep the tabs depressed and remove the spool cover

from the housing.

u Carefully clean the spool housing.

u Push the cover onto the housing until it snaps securely

into place.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 93 94

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GLC2500L Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Tondeuses à gazon Black & Decker GLC2500L