Black & Decker FP2650S Manuel d'utilisation et d'entretien télécharger pdf (Page 5)

4. Insert the food pusher into the central tube of the wide-mouth feed chute.

Turn clockwise to lock in place. The pusher is used to guide foods through

the feed chute and can be removed when adding liquid or additional foods

while the processor is running. To remove, turn counterclockwise.



The controls are located on the front of the base . Press

PULSE, HIGH or LOW to select a function (see directions

below).



• Processor should be stored in OFF position and unplugged

when not in use.

• Use PULSE for short processing tasks. This lets you control

the size and uniformity of foods being chopped.

• The OFF/PULSE button must be pressed and held for the appliance to operate

in PULSE mode. When released, the appliance will stop.

• The motor of the processor will run as long as the OFF/PULSE button is held

down. Press the button and then release to allow the blades to stop running

and the food to fall to the bottom of the workbowl.

• Pulsing gives better control when chopping, mincing, mixing and blending

foods. You can control the size of the foods, from coarse to fine.



When either speed is selected, the processor will run continuously until the OFF/

PULSE button is pressed.



The chopping blade is used to coarsely or finely chop, mince, mix and puree

foods to a smooth consistency.

1. Lock workbowl into position (see ).

2. Hold chopping blade by center shaft and insert onto center

post .





3. Place food in workbowl.

4. Place cover on workbowl and lock into place by rotating

clockwise (see ).

5. When using large workbowl, place the wide-mouth feed chute and food

pusher in place.



6. Select your desired speed (PULSE, LOW or HIGH).

 Process foods for no more than a few seconds at a time. Pulsing produces

excellent results and offers greater control.





7. If using small workbowl, press OFF/PULSE and wait for blades to stop

revolving. If using large workbowl, food can be added while processor is

running; remove food pusher and insert food through the feed chute. Replace

food pusher in chute.





8. Press the OFF/PULSE button and allow blades to stop revolving before

removing cover. Twist cover toward to remove.

9. Unlock workbowl by turning it counterclockwise and lift off base.

 Remove bowl from appliance before removing blade to prevent food from

leaking through the center opening of the bowl.

10. Carefully remove chopping blade.

11. Unplug appliance when not in use.



• The processor works very quickly.

• Watch carefully to avoid over-processing foods.

• The PULSE button offers the best control and results.

• For best results, process foods that are about the same size.

• Do not overload the bowl.

• Never walk away from the processor while it is on.

• Use hot but never boiling liquids.

• Do not process more than ¾ cup liquid in the small workbowl and 3 cups

liquid in the large workbowl at one time.

• To process meat, use no more than ¾ cup in the small workbowl and 2 cups

of ¾-inch cubes. Process using PULSE in 5 second intervals.

• The small workbowl has a capacity of 3 cups and the large workbowl has a

capacity of 10 cups.

• Insert a funnel into the feed chute when adding ingredients such as, oil, flour

and sugar.



This blade makes preparing dough efficient and time-saving.

1. Use this blade in the large workbowl. This blade does not extend to the

outside rim of the workbowl, so it cannot incorporate flour when very small

amounts of flour are being processed.

2. Push dough blade down as far as it will go into workbowl.

3. Insert all the dry ingredients into the workbowl.

4. Place cover on workbowl. Add wide-mouth feed chute and food pusher.

Process to blend.

5. Add liquids through the small feed chute with machine running.





1 2 3 4 5 6 7 8 9 10 ... 36 37

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FP2650S Manuel d'utilisation et d'entretien Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Transformateurs de denrées alimentaires Black & Decker FP2650S