• DON’T-Operate saw without guards in place.
• DON’T-Perform any operation freehand.
• DON’T-Reach around or behind saw blade.
• DON’T-Place hands closer than 6 inches
from the saw blade.
• DON’T-Reach underneath the saw unless it is
turned off and unplugged. The saw blade is exposed
on the underside of the saw.
• DON’T-Move either hand from saw or work-
piece or raise arm until blade has stopped.
• DON’T-Use without Kerf Plate or when kerf
slot is wider than 3/8"
• DON’T- Carry saw by work extension or
other accessory.
CAUTION: Some wood contains preserva-
tives such as copper chromium arsenate
(CCA) which can be toxic. When cutting these
materials extra care should be taken to avoid
inhalation and minimize skin contact.
CAUTION: Use of this tool can generate dust
containing chemicals known to cause cancer,
birth defects or other reproductive harm. Use
appropriate respiratory protection.
CAUTION: Do not connect unit to electrical
power source until complete instructions are
read and understood.
For your convenience and safety, the following
warning labels are on your miter saw.
ON MOTOR HOUSING:
WARNING:FOR YOUR OWN SAFETY, READ INSTRUC-
TION MANUAL BEFORE OPERATING SAW. WHEN
SERVICING, USE ONLY IDENTICAL REPLACEMENT
PARTS. ALWAYS WEAR EYE PROTECTION.
ON FENCE:
CLAMP SMALL PIECES BEFORE CUTTING. SEE MANUAL.
ON GUARD:
DANGER – KEEP AWAY FROM BLADE.
ON GUARD RETAINER PLATE: “PROPERLY SECURE
BRACKET WITH BOTH SCREWS BEFORE USE.”
ON TABLE: (2 PLACES)
ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE
USE. KEEP HANDS 6" FROM PATH OF SAW BLADE.
NEVER PERFORM ANY OPERATION FREEHAND.
NEVER CROSS ARMS IN FRONT OF BLADE. THINK!
YOU CAN PREVENT ACCIDENTS. DO NOT OPERATE
SAW WITHOUT GUARDS IN PLACE. NEVER REACH IN
BACK OF SAW BLADE. ALWAYS WEAR EYE PROTEC-
TION. SHUT OFF POWER AND WAIT FOR BLADE TO
STOP BEFORE SERVICING, ADJUSTING TOOL, OR
MOVING HANDS.
Electrical Connection
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of 10 percent or more will
cause a loss of power and overheating. All B&D tools are
factory tested. If this tool does not operate, check the
power supply.
Familiarization
Place the saw on a smooth, flat surface such as a work-
bench or strong table. Examine Figures 1 & 2 and refer
to the parts description to become familiar with the saw
and its various parts. The following section on adjust-
ments will refer to these terms and you must know what
and where the parts are. The part name is followed by
the corresponding part number Example - lock down pin
(10). Press down lightly on the operating handle and pull
out the lock down pin (10), as shown in Figure 3. Gently
release the downward pressure and allow the arm to rise
to its full height. Use the lock down pin when carrying the
saw from one place to another. Use the operating
handle (1) to transport the saw or the hand indentations
(11) shown in Figure 2 after unplugging.
Specifications
Capacity of cut
47° miter left and right
47° bevel left
0° miter -Max. Height 3-1/2” -Max. Width 5-1/2”
45° miter -Max. Height 3-1/2” -Max. Width 4-1/8”
45° bevel -Max. Height 2-1/2” -Max. Width 5-1/2”
27
(28 pages)
(32 pages)
(12 pages)
(12 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels