7
Features
1. Carrying strap
2. Speed control knob
3. On/off switch
4. Collection bag handle
5. Collection bag
6. Blow clamshell
7. Blow tube
8. Scraper
9. Vacuum tube - lower
10. Vacuum tube - upper
11. Locking ring
12. Release button
13. Powerhead
Assembly
Warning! Before assembly, make sure that the appliance is
switched off and unplugged.
Vacuum tube assembly (fig. A)
The vacuum tubes must be assembled together before use.
Warning! Do not operate the appliance with the vacuum
tubes separated.
X To ease assembly, apply a soapy water solution to the
joint area.
X Align the notches (15) and the triangles (14) on the
upper (10) and lower (9) vacuum tubes.
X Push the lower vacuum tube (9) firmly into the upper
vacuum tube (10) until the triangles click into place.
Warning! Do not separate the tubes once assembled.
Blow tube assembly (fig. B)
The blow tube must be assembled to the blow clamshell
before use.
X Align the circles (16) on the blow clamshell (6) and the
blow tube (7).
X Push the blow tube (7) firmly onto the blow clamshell (6)
until the circles click into place.
Warning! Do not separate the tubes once assembled.
Carrying strap assembly (fig. C - D)
Fit the carrying strap (1) to the appliance and adjust to suit
the user.
X Clip the hook (17) through the eyelet (18).
X Adjust the length of the loop with the buckle (19).
Use
Switching on and off (fig. E)
Warning! Use both hands to grip the product firmly when
switching on.
X To switch the appliance on, slide the on/off switch (3)
forward.
X To switch the appliance off, slide the on/off switch (3)
back.
Variable speed control (fig. E)
X For extra control, your blowvac is fitted with a speed
control knob (2) located on the handle of the
powerhead.
X Set the variable speed control knob (2) to the required
speed range.
Cable restraint (fig. F)
X A cable restraint (21) is incorporated into the rear of the
powerhead.
X Loop the cable (20) through the cable restraint (21).
Using your product (fig. G)
Warning! When using as a blower or vacuum, always wear
safety glasses. If using in dusty conditions, wear a filter mask
as well.
Warning! Switch off your product, allow the fan to stop and
remove the plug from the socket before carrying out any
adjustment, servicing or maintenance.
Blow mode (fig. G H and I)
Note: Make sure that the locking ring is in the unlocked
position (fig. I).
X Attach the blow clamshell (6) and tube (12 and 13) to the
powerhead (13) (Fig. G) by locating the blower as
indicated by the arrow, then pivot about this point and
press the locking/release catch (12) until catch (22) is
fully engaged.
X Turn the locking ring (11) clockwise to the locked
position.
X Hold the blow tube approximately 180mm above the
ground, switch on the appliance and using a sweeping
motion from side to side, advance slowly keeping the
accumulated debris/leaves in front of you (fig. H).
X Once you have blown the debris/leaves into a pile, you
can convert to vacuum mode to collect the debris.
Removing the blow/vacuum tube (fig. I)
X To disconnect the blow clamshell (6) or vacuum tube
(10) from the powerhead (13), turn the locking ring (11)
counter-clockwise to the unlock position, then press the
release button (12), making sure that the tube does not
fall to the ground.
X The release button (12) will not operate if the locking
ring (11) is in the locked position.
Vacuum mode (fig. J - N)
Fit the bag assembly to the blowvac (figs. J, K, L)
(32 pages)
(22 pages)
(28 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels