Black & Decker FP1610 Manuel d'instructions télécharger pdf (Page 4)

Safety Instructions For All Tools

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

• CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t

use power tools in damp or wet locations. Keep work area well lit. Do not use tool

in presence of flammable liquids or gases.

• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded sur-

faces. For example; pipes, radiators, ranges, and refrigerator enclosures.

• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All vis-

itors should be kept away from work area.

• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or

locked-up place — out of reach of children.

• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was

intended.

• USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-

duty tool. Don’t use tool for purpose not intended.

• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in

moving parts. Rubber gloves and non-skid footwear are recommended when

working outdoors. Wear protective hair covering to contain long hair.

• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.

• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from

receptacle. Keep cord from heat, oil, and sharp edges.

• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your

hand and it frees both hands to operate tool.

• DON’T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer

performance. Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and if damaged, have repaired by authorized ser-

vice facility. Inspect extension cords periodically and replace if damaged. Keep

handles dry, clean, and free from oil and grease.

• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when

changing accessories, such as blades, bits, cutters.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that

keys and adjusting wrenches are removed from tool before turning it on.

• AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be

sure switch is off when plugging in.

• EXTENSION CORDS. Make sure your extension cord is in good condition. When

using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. The following table shows the correct

size to use depending on cord length and nameplate ampere rating. If in doubt,

use the next heavier gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0-6 18161614

6 - 10 18 16 14 12

10-1216161412

12 - 16 14 12 Not Recommended

• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only exten-

sion cords intended for use outdoors and so marked.

• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool

when you are tired.

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part

that is damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that is damaged should be

properly repaired or replaced by an authorized service center unless otherwise

indicated elsewhere in this instruction manual. Have defective switches replaced

by authorized service center. Do not use tool if switch does not turn it on and off.

384282/6121/JUN97 5/2/02 2:00 PM Page 1

1 2 3 4 5 6 7 8 9 ... 12 13

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FP1610 Manuel d'instructions Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Ponceuses électriques Black & Decker FP1610