Black & Decker 200 WATT Manuel d'instructions télécharger pdf (Page 4)

Features

1. LED indicators

2. On/Off switch

3. Terminals

4. Battery clamps

5. 12 Vdc accessory plug (not BDPC750)

6. USB port

7. Mains socket

How the power inverter works

The power inverter converts low voltage dc (direct current)

from a battery or other power source to standard 230 Vac

(alternating current) household power.

The power inverter output waveform

The ac output waveform of the power inverter is known as a

“modified sine wave”.

This type of waveform is suitable for most ac loads, including

linear and switching power supplies used in electronic

equipment, transformers and motors.

Operating instructions

Power source requirements

The power source must provide 12 Vdc and must be able to

supply the necessary current to operate the load.

Warning! The power inverter must be connected only to

batteries with a nominal output voltage of 12 Volts. The

appliance will not operate from a 6 Volt battery and will

sustain permanent damage if connected to a 24 Volt battery.

Connection to a power source

The power inverter comes equipped with a 12 Vdc

accessory plug (5) and/or battery clamps (4) for connection

to a dc power source.

Note: For optimal performance make sure that the engine is

running while operating the inverter. However, the power

inverter may not operate while the engine is starting because

the battery voltage can drop substantially during cranking.

Connecting to a power source using the 12 Vdc

accessory plug (not model BDPC750)

Up to 100 W only

The 12 Vdc accessory plug (5) is suitable for operating the

power inverter at power outputs up to 100 Watts only. The tip

of the plug is positive (+) and the side contact is negative (-).

Warning! Connect the ring terminals to the terminals (3) of

the power inverter before connecting the accessory plug to

the accessory outlet. Make sure that the On/Off switch (2) is

turned off and that no flammable fumes are present in the

installation area.

X Connect the ring terminal of the red cable to the red

terminal (3) marked (+) on the back of the power

inverter.

X Connect the ring terminal of the black cable to the black

terminal (3) marked (-) on the back of the power inverter.

X Connect the power inverter to the power source by

inserting the 12 Vdc accessory plug (5) firmly into the

accessory outlet of a vehicle or other dc power source.

X Set the On/Off switch (2) to on.

X Plug the USB connector from the equipment you wish to

operate into the USB port (6) and operate as normal.

Note: On some vehicles the accessory socket may only

become live when the ignition key is in the accessory

position.

Warning! Do not use with positive ground electrical

systems, (i.e older vehicles).

Connecting to a power source using the cables (fig. C)

Above 100W

Use the cables and connect the appliance directly to the

12 Volt power source as follows:

X Make sure the appliance power is turned off and that no

flammable fumes are present in the installation area.

X Connect the red cable to the red terminal (3) marked (+)

on the back of the power inverter.

X Connect the black cable to the black terminal (3)

marked (-) on the back of the power inverter.

X Connect the red battery clamp (4) to the positive

terminal of the battery.

X Connect the black battery clamp (4) to the negative

terminal of the battery.

X Make sure that all connections between the battery

clamps (4) and the terminals (3) are secure.

X Set the On/Off switch (2) to on.

X Insert the plug from the the equipment you wish to

operate into the mains socket (7) and operate as

normal.

Warning! Loose connectors may cause overheated wires

and melted insulation. Check to make sure you have not

reversed the polarity. Damage due to reversed polarity is not

covered by our guarantee.

Warning! A reverse polarity connection will result in a blown

fuse and may cause permanent damage to the power

inverter.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 200 WATT Manuel d'instructions Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Adaptateurs et onduleurs de puissance Black & Decker 200 WATT