Black & Decker FS1402D Manuel d'instructions télécharger pdf (Page 2)

forward/reverse control button the opposite direction. The center position of the control

button locks the tool in the off position. When changing the position of the control button, be

sure the trigger is released.

Torque Control - Figure 4

This tool is fitted with a collar to select the operating mode and to set the torque for

tightening screws. Large screws and hard workpiece materials require a higher torque

setting than small screws and soft workpiece materials.

• For drilling in wood, metal and plastics, set the collar to the drilling position symbol .

• For screwdriving, set the collar to the desired setting. If you do not yet know the appro-

priate setting, proceed as follows:

• Set the collar to the lowest torque setting.

•Tighten the first screw.

• If the clutch ratchets before the desired result is achieved, increase the collar setting

and continue tightening the screw. Repeat until you reach the correct setting. Use this

setting for the remaining screws.

Dual Range Gearing - Figure 5

The dual range feature of your drill allows you to shift gears for greater versatility. To select

low speed, high torque setting (position 1), turn tool off and permit to stop. Slide gear shifter

button forward towards the chuck. To select the high speed, low torque setting (position 2),

turn tool off and permit to stop. Slide gear shifter button back (away from chuck). NOTE:

Do not change gears when tool is running. If you are having trouble changing gears, make

sure that the dual range gear button is either completely pushed forward or completely

pushed back.

Keyless Chuck

To insert a drill bit or other accessory:

1. Grasp the chuck collar (containing the two orange buttons) with one hand and use your

other hand to rotate the chuck in the counterclockwise direction, as viewed from the

chuck end.

2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the

collar behind the chuck (containing the two orange buttons) and rotating the chuck in

the clockwise direction as viewed from the chuck end.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the

front part of the chuck and turning the tool on. Damage to the chuck and personal injury

may occur when changing accessories.

Removable Chuck with Quick Connect

Bit Change System - Figure 6

Another unique feature of your drill is the ability to remove the chuck quickly and easily.

This allows for a drill bit to be in the keyless chuck, while another accessory such as a

screwdriver bit, can be inserted into the Quick Connect

hex shaft at the same time.

To remove the chuck:

1. Grasp the drill and depress the two orange buttons on the chuck collar as shown in

Figure 6.

2. With the buttons depressed, pull straight out.

To replace the chuck:

1. Push the quick connect chuck straight on with a slight twisting motion until you hear it

click into place.

To insert a screwdriver bit into the Quick Connect

hex shaft, push the bit in until you hear

it click into place. To remove the bit, hold the drill as shown in Figure 7. Push in evenly on

the spring loaded disc with two fingers and pull the bit straight out.

Screw Driving

For driving fasteners, the reversing button should be pushed to the left. Use reverse (button

pushed to the right) for removing fasteners. When moving from forward to reverse, or vice

versa, always release the trigger switch first.

On Board Bit Storage

Abit storage slot is built-in to the area just above the battery.

Drilling

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the Safety Instructions.

• Use appropriate and required safety equipment, as instructed in the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety Instructions.

• Run the drill very slowly, using light pressure, until the hole is started enough to keep the

drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the drill firmly with one hand on the grip and the other hand on the bottom of the

battery pack to control its twisting action.

• DO NOT CLICK THE TRIGGER OF ASTALLED DRILLOFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the

last part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Make sure switch turns drill on and off.

WARNING: It is important to support the work properly and to hold the drill firmly to

prevent loss of control which could cause personal injury. If you have any questions on how

to properly operate tool, call: 1-800-544-6986.

Drilling in Wood

Holes in wood can be made with the same twist drill bits used for metal or with spade bits.

These bits should be sharp and should be pulled out frequently when drilling to clear chips

from the flutes.

Drilling in Metal

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.

Drilling in Masonry

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but

not so much that you crack the brittle material. Asmooth, even flow of dust indicates the

proper drilling rate.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

An occasional application of a household oil to the Quick Connect

hex shaft will help

prevent rust.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service organizations, always using identical

replacement parts.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already been paid by

Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the

trash or municipal solid waste stream and the RBRC program provides an environmentally

conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent

nickel-cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1-800-8-BATTERY.

Accessories

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

The following accessories should be used only in the sizes specified below:

BITS, METALDRILLING – Up to 3/8" (9.5mm); BITS, MASONRY DRILLING – Up to 3/8"

(9.5mm); WOOD DRILLING – Up to 1/2" (12.7mm).

Safety Warnings and Instructions: Charging the Drill

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using battery.

3. CAUTION: To reduce the risk of injury, charge only Black & Decker Battery Packs.

Other types of batteries may burst causing personal injury and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed

extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must

be suitable for outdoor use. Any cord marked for outdoor use can also be used for

indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable

for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety, and to prevent loss of power and overheating. The smaller the gauge number of

the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than

18 gauge. When using more than one extension to make up the total length, be sure

each extension contains at least the minimum wire size.

CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS

NAMEPLATE RATING AMPS – 0 – 10.0

Total Extension Cord Length (ft) 25 50 75 100 125 150

Wire Gauge 18 18 16 16 14 14

9. Use only the supplied charger when charging your drill. The use of any other charger

could damage the drill or create a hazardous condition.

10.Use only one charger when charging.

11. Do not attempt to open the charger or the drill. There are no customer serviceable parts

inside. Return to any authorized Black & Decker service center.

12.DO NOT incinerate the drill or battery packs even if they are severely damaged or

completely worn out. The batteries can explode in a fire.

13.A small leakage of liquid from the battery cells may occur under extreme usage,

charging or temperature conditions. This does not indicate a failure. However, if the

outer seal is broken and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10

minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a

25-35% solution of potassium hydroxide.

Charging Procedure

Your charger is designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any

other voltage. Charge time is 60 minutes depending on battery pack type and condition.

1. Plug the charger into an appropriate outlet. NOTE: Do not charge by means of an

engine generator or DC power source. Use only 120V AC.

2. Insert the battery pack into the charger (Figure 1). Be sure the pack is fully seated in the

charger. The red (charging) light will blink continuously indicating that the charging process

has started.

3. The completion of charge will be indicated by the red light remaining ON continuously. The

battery pack is fully charged and may be used at this time or left in the charger.

4. Unplug charger, and remove the battery pack. Place the battery in the tool and be

certain that it is inserted fully into the tool cavity until it “clicks” into place.

NOTE: To remove the battery pack from the product, press down on the release button

on the back of the battery (Figure 2) and pull out.

Replace Pack

The charger is designed to detect certain problems that can arise with battery packs which

would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack.

If problem persists, try a different battery pack to determine if the charger is OK. If the new

pack charges correctly, then the original pack is defective and should be returned to a service

center for recycling. If the new battery pack gives the same trouble indication as the original,

have charger tested at an authorized service center.

Wall Mounting (Figure 2A)

A hole is provided in the center of the charger for mounting on a vertical surface.

Leaving the Battery Pack in the Charger

The charger and battery pack can be left connected with the red light glowing indefinitely. The

charger will keep the battery pack fresh and fully charged.

NOTE: Abattery pack will slowly lose its charge when kept out of the charger. If the battery

pack has not been kept on maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when

the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery

pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is

important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a

normal condition, and does not indicate a problem.

3. If the battery pack does not charge properly — (1) Check power at receptacle by

plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a

light switch which turns power off when you turn out the lights. (3) Move charger and

battery pack to a location where the surrounding air temperature is approximately

65°F - 75°F (18°- 24°C). (4) If charging problems persist, take or send the tool, battery

pack and charger to your local service center.

4. The battery pack should be recharged when it does not produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE use under these conditions.

Follow the charging procedures. You may also charge a partially used pack whenever

you desire with no adverse affect on the battery pack.

5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers

labeled “NiMH“ or “NiCd/NiMH.”

6. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or

any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

7. Do not immerse charger in water or any other liquid.

Safety Warnings and Instructions: Drills

1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the

battery pack.

2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.

WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always

expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control

which could cause personal injury. If a stall does occur, release the trigger immediately

and determine the reason for the stall before re-starting.

Operating Instructions

Trigger Switch & Forward/Reverse Button - Figure 3

The drill is turned ON and OFF by pulling and releasing the trigger switch shown in

Figure 3. The farther the trigger is depressed, the higher the speed of the drill. A

forward/reverse control button determines the direction of the tool and also serves as a lock

off button. To select forward rotation, release the trigger switch and depress the

forward/reverse control button as depicted in Figure 3. To select reverse, depress the

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FS1402D Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Perceuses combinées sans fil Black & Decker FS1402D