Black & Decker HX210-QS Manuel d'instructions télécharger pdf (Page 6)

ENGLISH

(Original instructions)

Check the polarity of the battery posts. A positive (POS,P, +)

battery post usually has a larger diameter than the negative

(NEG, N, -) battery post.

Connect the positive (red) clamp from the battery charger to

the positive (POS, P, +) post of the battery.

Connect the negative (black) clamp from the battery charger

to the negative (NEG, N, -) post of the battery.

When disconnecting the battery charger from the battery,

always:

u Switch off and unplug the battery charger.

u Remove the negative (black) clamp rst.

u Remove the positive (red) clamp last.

u Ret any insulating covers to the battery posts.

Use

Connecting the appliance with the battery clamps

(g. A)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the battery clamps (3) to the battery charger with

the in-line connector (6).

u The appliance's output leads have colour-coded battery

clamps (3) (red-positive and black-negative). These

connect directly to the corresponding connectors on the

battery terminals.

u Follow the steps outlined in "Safety instructions" at the

front of this manual.

u Insert the ac plug of the battery charger into an ac mains

socket.

Connecting the appliance with the ring terminals

(g. A & B)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the ring terminals (4) to the battery charger with

the in-line connector (6).

u The output leads have crimped, colour-coded ring

terminals (4) (red-positive and black-negative). The ring

terminals (4) connect directly to the corresponding con-

nectors on the battery terminals.

u Remove the nuts from the bolts of the battery terminal's

connectors (g. B).

u Install the red ring terminal (4) to the bolt of the positive

battery terminal connector and replace the nut.

u Install the black ring terminal (4) to the bolt of the negative

terminal connector and replace the nut.

u Insert the ac plug of the battery charger into an ac mains

socket.

Connecting the appliance with the dc accessory

plug (g. A)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the dc accessory plug (5) to the battery charger

with the in-line connector (6).

u Insert the dc accessory plug (5) into the vehicle's dc ac-

cessory outlet.

u Insert the ac plug of the battery charger into an ac mains

socket.

Charging Indicators

u Red LED (2) - bad connection, the battery is not able to

accept charge or a reverse polarity connection has been

detected.

u Flashing green LED (2) - good connection and the battery

is charging.

u Solid green LED (2) - the battery is fully charged.

When the appliance is properly connected, the yellow LED will

illuminate, indicating that the smart circuit is functioning to as-

sess the status of the battery. This procedure may take up to 2

minutes if the battery voltage is lower than 12.8 Volts.

The appliance is fully automatic; it will power on when needed

and power off when the battery is fully-charged.

The appliance has built-in circuit protection which guards

against overcharging or short circuits.

Charging the battery (g. C)

u Slide the charge voltage selector switch (1) to the 6V or

12V position as required.

u Leave the appliance on.

u Monitor the battery from time to time.

Note: A clicking sound may occur during the charging proc-

ess, this is normal.

u When the solid green LED is lit, the battery is fully

charged.

u Remove the ac plug from the ac mains socket.

u Remove the charging leads from the battery.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker HX210-QS Manuel d'instructions Page 6

Commentaires sur ces manuels