Black & Decker KR554CRES Manuel d'instructions Page 6
- Page / 80
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6
ENGLISH
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will make sure that the safety of the power tool is
maintained.
Additional power tool safety warnings
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
Safety of others
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Labels on tools
The following pictograms are shown on the tool.
Electrical safety
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Warning! Additional safety warnings for drills and
impact drills.
!
Warning! To reduce the risk of injury, the user must
read the instruction manual.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
- KR504CRE 1
- KR504CRES 1
- KR554CRES 1
- Intended use 5
- Safety instructions 5
- Features 7
- Assembly 7
- Fitting a drill bit 7
- Accessories 8
- Maintenance 8
- Protecting the environment 8
- EC declaration of conformity 9
- Guarantee 9
- Bestimmungsgemäße Verwendung 11
- Sicherheitshinweise 11
- Merkmale 13
- Einsetzen eines Bohreinsatzes 13
- Gebrauch 14
- Umweltschutz 15
- EU-Konformitätserklärung 16
- KR504RE, KR504CRE 16
- KR504CRES, KR554RE, KR554CRES 16
- Garantie 16
- FRANÇAIS 17
- ITALIANO 23
- NEDERLANDS 29
- Uso previsto 35
- Instrucciones de seguridad 35
- Características 37
- Montaje de una broca 37
- Accesorios 38
- Mantenimiento 38
- Protección del medio ambiente 39
- Declaración de conformidad CE 40
- KR554RE, KR554CRES 40
- Garantía 40
- PORTUGUÊS 41
- Användningsområde 47
- Säkerhetsinstruktioner 47
- Funktioner 49
- Montering 49
- Sätta i ett borr 49
- Användning 49
- Tillbehör 50
- Underhåll 50
- Bruksområde 53
- Sikkerhetsinstrukser 53
- Funksjoner 55
- Sette inn et bor 55
- Tilbehør 56
- Vedlikehold 56
- Samsvarserklæring for EU 57
- Anvendelsesområde 58
- Sikkerhedsvejledninger 58
- Montering af bor 60
- Anvendelse 60
- Vedligeholdelse 61
- Miljøbeskyttelse 61
- EU overensstemmelseserklæring 62
- Käyttötarkoitus 64
- Turvallisuusohjeet 64
- Yleiskuvaus 66
- Kokoaminen 66
- Poranterän asentaminen 66
- Lisävarusteet 67
- Ympäristönsuojelu 67
- EU:n yhdenmukaisuusilmoitus 68
- ΕΛΛΗΝΙΚΑ 70
- KR554RE - KR554CRES 77
© 2020, manymanuals.fr. Tous droits réservés | 2.600 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels