Black & Decker FSM1630-XE Manuel d'instructions télécharger pdf (Page 9)

ENGLISH

(Original instructions)

Steam cleaning



loop’ side facing up.

 Raise the steam mop off the resting mat (8) and lightly

press it down onto the cleaning pad (6 or 7).

 Place the steam mop on the resting mat.

 Connect the steam mop to the mains.

 Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

 Press the Smartselect

button (2) till the required setting

is reached.

 Pulling the handle (4) back will activate the steam pump.

After a few seconds steam will start to come out of the

steam head.

 It takes a few seconds for steam to enter the cleaning pad.

The steam mop will now glide easily over the surface to be

sanitised/cleaned.



thoroughly steam clean each section.

Note: During use you may turn off the steam pump by return-

ing the handle to the upright position, this convenient feature

will allow you to place the steam mop on the resting mat for

a short time so that you may move items of furniture, then

continue cleaning without the need to switch the appliance off.



handle (4) to the upright position and turn it ‘OFF’, place it

on the resting mat (8) and wait until the steam mop cools

Caution! It is important to monitor the water level in the water

return the handle (4) to the upright position and turn the steam

mop ‘OFF’. Unplug the unit from the electrical wall outlet,

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop on

the resting mat (8) with the handle (4) in the upright position

when stationary and make sure the steam mop is turned off

when not in use.

Carpet refreshing



loop’ side facing up.

 Raise the steam mop off the resting mat (8) and lightly

press it down onto the cleaning pad (6 or 7).



 Lightly press the steam mop down onto the carpet glider

(9) until it clicks into place.

 Place the steam mop on the resting mat. (8)

 Connect the steam mop to the mains.

 Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

 Press the Smartselect

button (2) to the Wood/Laminate

setting.

 Pulling the handle (4) back will activate the steam pump.

After a few seconds steam will start to come out of the

steam head.

 Push and pull the steam mop slowly across the carpet to

thoroughly refresh each section.

Note: During use you may turn off the steam pump by return-

ing the handle (4) to the upright position, this convenient

feature will allow you to place the steam mop on the resting

mat (8) so that you may move items of furniture with out the

need to switch the appliance off.



handle (4) to the upright position and turn it ‘OFF’, place it

on the resting mat (8) and wait until the steam mop cools

Caution! It is important to monitor the water level in the water

return the handle (4) to the upright position and turn the steam

mop ‘OFF’. Unplug the unit from the electrical wall outlet,

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop on

the resting mat (8) with the handle (4) in the upright position

when stationary and make sure the steam mop is turned off

when not in use.

After use (Fig. J & K)

 Return the handle (4) to the upright position and turn the

steam mop ‘OFF’,

 Place the steam mop on the resting mat (8) and wait until

 Unplug the steam mop from the electrical wall outlet.

 Empty the water tank (3).

 Remove the cleaning pad (6 or 7) and wash it ready for

next use. (Take care to follow the wash care instructions

printed on the cleaning pad).

 Wrap the supply cable around the cable tidy hooks (10 &

11).

Note: The top cable tidy hook (11) rotates to easily release the

cable ready for next use.

 Clip the supply cable onto itself using the cable tidy clip

(22) close to the plug.

 Place steam mop on the resting mat (8) for storage.

Note: With the handle (4) in the upright position, the cable

neatly wrapped around the cable tidy hooks (10 & 11) and

secured with the cable tidy clip (22) your steam mop will stand

on its own for storage. Alternatively there is a hanging bracket

(23) built into the hand grip (24) which will allow your steam

mop to be hung from a suitable hook on the wall. Always

ensure that your wall hook is capable of supporting the weight

of the steam mop safely.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker FSM1630-XE Manuel d'instructions Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Nettoyeurs à vapeur Black & Decker FSM1630-XE