Black & Decker CI500 Manuel d'utilisateur télécharger pdf (Page 4)

ENGLISH

The operator should not attempt specialised

applications or repairs (e.g. repairing electrical

appliances) unless qualified or trained to do so.

This appliance is not a toy. Keep out of the reach of

children.

Safety symbols marked on appliance

Hot surface do not touch.

Electrical safety

This product must be earthed. Always check that

the power supply corresponds to the voltage on

the rating plate.

Power plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (Class 1)

power tools. Unmodified plugs and matching outlets will

reduce the risk of electric shock.

Extension cables & Class 1 product

X A 3-core cable must be used as your appliance is earthed

and of Class 1 construction.

X Up to 30 m (100 ft) can be used without loss of power.

X This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. Handy storage bin

2. Coiled spring support

3. Ready-for-use indicator

4. Temperature selector

5. Handle

6. Flexible arm grippers

7. Sponge

8. Soldering iron stand

Assembly

Warning! Before cleaning, adjustment or changing the

attachments. Unplug the appliance and allow the attachment

to cool.

Fitting the craft soldering iron support (fig. A)

Insert the coiled spring support (2) into the craft soldering

iron stand (8) by aligning the protrusions on the support with

the slots in the opening. Push the support straight in until it

"clicks" into place.

Cable storage

The channel around the bottom of the stand (8) serves as a

cord wrap for the cord.

Heating attachment storage (fig. B)

A handy storage (1) bin is built-in to the base of the craft

soldering iron stand (8). To remove the bin from the base of

the stand (8), press in on the sides and pull out.

Fitting and removal of a heating attachment

To fit a heating attachment to the craft soldering iron, select

the attachment required. Ensure the attachment is clean and

that the handle socket is free from debris.

Insert the threaded end into the craft soldering iron and

rotate clockwise. Tighten by hand to secure. Do not use

pliers or hand tools.

To remove the heating attachment, unplug the craft

soldering iron and allow the attachment to cool. Rotate the

tip anticlockwise.

Fitting and removing the knife point (fig. C)

Warning! Cut hazard. The knife blade is razor sharp. Use extra

care when handling the knife blade at all times.

Place the knife into the holder, and then place the holder into

the sleeve.

Carefully thread the assembly onto the craft soldering iron

handle. Rotate the holder clockwise and hand-tighten.

To remove the knife point

Unplug the craft soldering iron and allow the attachment to

cool. Rotate the holder anticlockwise.

Use

Warning! Be aware that this product may ignite material.

Where this is a concern, test a piece of scrap material.

Turning the appliance on

To turn the appliance on, insert the plug into an appropriate

socket. The heating element will begin to heat up as soon as

the appliance is plugged in.

Heat selection (fig. D)

Push the switch to select either the low (I) setting or high

setting (II).

Use the high setting (II) for wood burning and soldering

applications and the low setting (I) for iron-on/plastics,

paper and fabric.

Ready for use indicator (fig. D)

A ready-for-use indicator (3) is built in to the handle (5) of the

craft soldering iron.

At room temperature the indicator (3) is grey.

When the Iron has reached the low (I) setting

(approximately 5 min.) the indicator (3) is yellow.

When the indicator (3) shows red, the tip has reached the

high (II) temperature setting (approximately 10 min).

1 2 3 4 5 6 7 8 9 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Black & Decker CI500 Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Fers à souder Black & Decker CI500