Black & Decker CI500 Manuel d'utilisateur télécharger pdf (Page 3)

ENGLISH

Intended use

Your Black & Decker Craft Soldering Iron has been designed

for leisure and DIY activities in the home including soldering,

woodburning, scrapbooking and Image transfer.

This tool is intended for consumer use only.

Safety instructions

Warning! When using mains-powered appliances, basic safety

precautions, including the following, should always be followed

to reduce the risk of fire, electric shock, personal injury and

material damage.

X Read all of this manual carefully before using the

appliance.

X The intended use is described in this manual. The use of

any accessory or attachment or the performance of any

operation with this appliance other than those

recommended in this instruction manual may present a risk

of personal injury.

X Retain this manual for future reference.

Using your appliance

X Keep work area clean and well lit. Cluttered and dark areas

invite accidents.

X Do not expose the appliance to rain or wet conditions.

Water entering the appliance will increase the risk of

electric shock.

X Stay alert, watch what you are doing and use common

sense when operating the appliance. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

X Never pull the power supply cord to disconnect the plug

from the socket. Keep the power supply cord away from

heat, oil and sharp edges.

X If the power supply cord is damaged during use, disconnect

the appliance from the power supply immediately. Do not

touch the power supply cord before disconnecting from the

power supply.

X Disconnect the appliance from the power supply when not

in use, before fitting or removing parts and before cleaning.

Safety of others

X Do not allow children or any person unfamiliar with these

instructions to use the appliance.

X Do not allow children or animals to come near the work

area or to touch the appliance or power supply cord. Close

supervision is necessary when the appliance is used near

children.

After use

X Switch off and remove the plug from the socket before

leaving the appliance unattended and before changing,

cleaning or inspecting any parts of the appliance.

X When not in use, the appliance should be stored in a dry

place. Children should not have access to stored

appliances.

Inspection and repairs

X Before use, check the appliance for damaged or defective

parts. Check for breakage of parts, damage to switches and

any other conditions that may affect its operation.

X Do not use the appliance if any part is damaged or

defective.

X Have any damaged or defective parts repaired or replaced

by an authorised repair agent.

X Before use, check the power supply cord for signs of

damage, ageing and wear.

X Do not use the appliance if the power supply cord or mains

plug is damaged or defective.

X If the power supply cord or mains plug is damaged or

defective it must be repaired by an authorised repair agent

in order to avoid a hazard. Do not cut the power supply cord

and do not attempt to repair it yourself.

X Never attempt to remove or replace any parts other than

those specified in this manual.

Specific safety instructions for craft soldering irons

Warning! This appliance must be placed on the stand (8) when

not in use.

DO NOT TOUCH THE HEATED TIP OF THE TOOL OR THE

HOT MELTED SOLDER. The operating temperature of this

appliance is approximately 465 °C on the high (II) setting and

300 °C on the low (I) setting.

The Heating element will begin to heat up as soon as

the appliance is plugged in. To avoid injury or damage to

property always assume that the appliance is hot and return

it to the protective stand (8).

Before cleaning, adjustment or changing the

attachments. Unplug the appliance and allow the

attachment to cool.

Keep the appliance away from all flammable material.

Be aware that this product may ignite material. Where this

is a concern, test a piece of scrap material.

Never leave the appliance plugged in and unattended.

After use, unplug the appliance, allow the attachment to

cool and store in a safe place out of the reach of children.

Fumes resulting from heating materials for craft

activities may be hazardous. Always work in a well

ventilated area. Seek advice on the materials being used.

Do not dip the tool into a liquid.

Keep hands away from the heated attachment and

work area. Heat may be conducted through the work piece.

Use clamps or pliers to hold the work piece.

Protect the work surface and materials from heat

damage. Heat may be conducted through the work piece.

Use a heat resistant material to protect the work surface.

1 2 3 4 5 6 7 8 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Black & Decker CI500 Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Fers à souder Black & Decker CI500