Black & Decker freewire Manuel d'instructions télécharger pdf (Page 2)

Step by step operating instructions for the OUTDOOR LAMP RECEIVER

A Quick Note before You Set Up the OUTDOOR LAMP RECEIVER:

The OUTDOOR LAMP RECEIVER can be used indoors and outdoors.

WARNING: When used outdoors, only use with outlets equipped with ground fault protection.

WARNING: Do not submerge. Keep connections dry. Failure to do this could result in electric shock.

WARNING: Read and understand warnings on your extension cord. Failure to do this could result in electric shock.

WARNING: To prevent shock hazard, always assume the power is present even if the red indicator light is not lit. Failure to do this could result in electric shock.

WARNING: Do not abuse extension cord. Do not yank extension cord to disconnect it from receptacle. Keep cord from heat, oil and sharp edges. Periodically inspect extension cords and

replace if damaged. Failure to do this could result in electric shock.

Unlike LAMP and APPLIANCE RECEIVERS the OUTDOOR LAMP RECEIVER does not have any code wheels. You set its code up from the MESSENGER HUB and it then remembers this

code, even after a power outage. For ease of programming, initially place the OUTDOOR LAMP RECEIVER in the same wall outlet that the MESSENGER HUB is plugged into. After

programming you can move it to its final location.

Step 1:

Set the unit code on the INDOOR REMOTE to the color and number that you want to use to control the OUTDOOR LAMP RECEIVER in its final location. (Example : Blue 11)

Step 2:

Plug the OUTDOOR LAMP RECEIVER into the same wall outlet

as the MESSENGER HUB or you can move the MESSENGER HUB and plug into the same wall outlet

as the OUTDOOR LAMP RECEIVER. (The Messenger Hub will not lose its memory and it can be moved back later.) See Figure 1. The red indicator light on the OUT-

DOOR LAMP RECEIVER should now be on.

Within 30 seconds of plugging OUTDOOR LAMP RECEIVER in, press and hold for 5 seconds the on button on the INDOOR REMOTE that corresponds to the UNIT

CODE that you have selected. After a few seconds, the red indicator light on the OUTDOOR LAMP RECEIVER will flash indicating that the code has been learned. If the

switch in the OUTDOOR LAMP RECEIVER is on, the red indicator light will remain lit. If the OUTDOOR LAMP RECEIVER switch is off, the red indicator light will not be lit.

NOTE: If the red indicator light does not turn on in 5 seconds, unplug

the OUTDOOR LAMP RECEIVER, re-plug and repeat step 2. If indicator light still does not turn on,

move the MESSENGER HUB and OUTDOOR LAMP RECEIVER to a different outlet in a different room and repeat step 2.

Step 3:

You may now move the OUTDOOR LAMP RECEIVER to its final location.

CAUTION: For outdoor use with extension cords: Plug OUTDOOR LAMP RECEIVER directly into wall outlet, then plug “outdoor rated” extension cord into

OUTDOOR LAMP RECEIVER to reduce the risk of electric shock.

OUTDOOR LAMP RECEIVER NOTES:

1.) OUTDOOR LAMP RECEIVER can be used with incandescents, fluorescents, halogens and low voltage lights rated up to 500 watts.

2.) If outlet is controlled by a wall switch, you must leave wall switch on at all times otherwise the OUTDOOR LAMP RECEIVER will not have AC power and you won’t be able to control it

remotely.

3.) To change the unit code, that the OUTDOOR LAMP RECEIVER responds to, unplug OUTDOOR LAMP RECEIVER and repeat steps 1 through 3.

4.) Unplug OUTDOOR LAMP RECEIVER when not in use.

5. Operating Temperatures -4°F to 122°F.

Storage Temperatures -40°F to 158° F

TROUBLESHOOTING

DIFFICULTY PROGRAMMING RECEIVERS

If you are experiencing problems when programming the BULB RECEIVER or OUTDOOR LAMP RECEIVER, it may be due to electrical interference on the power lines caused by large

appliances such as refrigerators or TV’s. To avoid the interference, move the RECEIVER and the MESSENGER HUB while it is being programmed to a different wall outlet that is further

away from large appliances.

SOME RECEIVERS DON’T RESPOND

Most houses are fed from a 240 volt service which is then split into two phases of 120 volts each in the circuit breaker panel. The most commonly encountered problem with systems which

use the existing house wiring to transmit signals is that the signals are received by some Receivers, but not by others. For example, the MESSENGER HUB controls some lights but not oth-

ers or controls some lights intermittently. This can happen sometimes when the Receiver to be controlled is on the opposite phase of the house wiring to the phase which the MESSENGER

HUB is connected to.

If some of the Receivers are not working it may be necessary to:

• move the Receiver to a different wall outlet to test that it works.If it still doesn’t work:

• move the Receiver to a different room. If it still doesn’t work:

• move the Receiver to the closest outlet that the MESSENGER HUB is plugged into or move the MESSENGER HUB to the closest outlet to the Receiver that is not working.

RECEIVERS TURN ON BY THEMSELVES

If it is suspected that Receivers have turned on or off by themselves, it is possible that a neighbor has a FREEWIRE or compatible system, which could result in unexpected operation of both

systems. Unplug all FREEWIRE devices immediately until (1) the interference is identified and eliminated through selection of a different HOUSE CODE to ensure that neither system causes

unintended operation of the other system or (2) a blocking filter, Black and Decker Model number PZZ01, is installed. Call 1-888-678-7278 to order. Professional installation recommended.

If you cannot identify the source of interference by talking with neighbors who are using a FREEWIRE or compatible system and you do not want to install a blocking filter, or if you have any

questions about identifying or eliminating interference, please call 1-800-544-6986 before plugging in or using any FREEWIRE device.

THREE WAY BULBS

Three way bulbs may be used, however, only one level of brightness can be activated using the Freewire system. To change brightness level you will need to turn the switch at the lamp to

the desired level of brightness.

NOTE: When using the BULB RECEIVER, you cannot control the lamp by the lamp’s switch. Turning the lamp switch off and then sending a Freewire signal within 30 seconds of power

being applied to the lamp, will cause the BULB RECEIVER to go into program mode and will need to be reprogrammed. See BULB RECEIVER section / manual.

INTERCOM AND MONITORING SYSTEMS

Intercom and monitoring systems, including baby monitors, that use the house wiring to transmit signals can “block out” FREEWIRE transmissions while the intercom or monitoring system is

in “permanent transmit” or “talk” mode. It is NOT possible to have a wireless intercom or monitoring system and a MESSENGER HUB operating in the same house. It is possible that a

neighbor’s wireless intercom or monitoring system could cause unexpected operation, including failure to operate, of your FREEWIRE system, or that your FREEWIRE SYSTEM could cause

unexpected operation, including failure to operate, of your neighbors intercom or monitoring system.

KEY CHAIN REMOTE RANGE OF USE

Placing the MESSENGER HUB on the inside wall closest to driveway or entry way, will often maximize range of KEY CHAIN REMOTE.

MAINTENANCE

Use only mild soap and damp cloth to clean the product. Never let any liquid get inside the product; never immerse any part of the product into a liquid. Avoid using solvents when cleaning

plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986. WARNING: The use of any accessory not recommended for use with this tool could be hazardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to

provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest

you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986.

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two

ways.

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made

within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return pol-

icy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under "Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, con-

tact the manager of your nearest Black & Decker Service Center.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

1 2

INSTRUCTION MANUAL 1
TROUBLESHOOTING 2

Commentaires sur ces manuels

Pas de commentaire

Black & Decker freewire Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Télécommandes Black & Decker freewire