Black & Decker LI3100 Manuel d'instructions télécharger pdf (Page 6)

10. Do not attempt to open the charger. There are no customer serviceable parts inside.

Return to any authorized Black & Decker service center.

11. DO NOT incinerate the tool or batteries even if they are severely damaged or

completely worn out. The batteries can explode in a fire. Toxic fumes and materials

are created when lithium ion battery packs are burned.

12. Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger

may ignite the dust or fumes.

13. If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for

three minutes or until irritation ceases. If medical attention is needed, the battery

electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or

flame.

Charging Procedure

CHARGING PROCEDURE - FIGURE B

IMPORTANT: The batteries in your tool are not fully charged at the factory. Before

attempting to charge them, thoroughly read all of the safety instructions.

(1) The charging socket (5) is keyed to lock out other chargers. Align the tab in the charger

plug (6) with the key in the charging socket.

(2) Plug the charger output plug (6) into the charging socket (5) of the tool as shown in

figure B.

(3) Plug the charger (7) into any standard 120 Volt 60 Hz electrical outlet.

(4) Let the tool charge initially for at least 12 hours. After the initial charge, your tool should

be fully charged in 12 hours from a fully discharged condition. Recharge discharged

batteries as soon as possible after use or

battery life may be greatly diminished. For

longest battery life, do not discharge

batteries fully. It is recommended that the

batteries be recharged after each use.

WARNING: Do not use tool while it is

connected to the charger.

WARNING: Fire Hazard. When

disconnecting the charger from the tool, be

sure to unplug the charger from the outlet

first, then disconnect the charger cord from

the tool.

Important Charging Notes

1. Your tool was sent from the factory in an

uncharged condition. Before attempting to

use it, it must be charged for at least 12

hours.

2. CAUTION: To reduce the risk of damage to

the batteries, NEVER charge them in an

air temperature below 40°F (4,5°C) or above 105°F (40,5°C). Also, NEVER charge

them if the battery temperature is below 40°F (4,5°C) or above 105°F (40,5°C).

Longest life and best performance occurs when batteries are charged with an air

temperature of approximately 75°F (24°C).

3. While charging, the charger may hum and become warm to touch. This is a normal

condition and does not indicate a problem.

4. If the batteries do not charge properly—(1) Check current at receptacle by plugging in

a lamp or other appliance. (2) Check to see if receptacle is connected to a light

switch which turns power off when you turn out the lights. (3) Check that the charger

plug is fully inserted into the charger port on the tool. (4) If the receptacle is OK, and

you do not get proper charging, take or send the tool and charger to your local

Black & Decker service center. See Tools Electric in yellow pages.

5. The tool should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. Battery life may be greatly diminished if batteries are

discharged deeply. DO NOT CONTINUE using product with its batteries in a depleted

condition. Recharge discharged batteries promptly.

90550370 LI3100.qxd 5/4/09 8:00 AM Page 6

1 2 3 4 5 6 7 8 9 10 11 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Black & Decker LI3100 Manuel d'instructions Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques Black & Decker LI3100