Black & Decker 90564630 Manuel d'utilisateur télécharger pdf

10 11

Troubleshooting

Problem Possible Cause Possible Solution

• Battery will not charge. • Charger not plugged into • Plug charger into a

a working outlet. working outlet. Refer to

“Important Charging

Notes” for more details.

• Check current at

receptacle by plugging in

a lamp or other appliance.

• Check to see if

receptacle is connected to

a light switch which turns

power off when you turn

out the lights.

• Surrounding air temperature • Move charger and tool

too hot or too cold. to a surrounding air

temperature of above 40

degree F (4,5°C) or below

105 degree F (+40,5°C).

• Tool will not drill. • Torque adjustment collar in • Move collar position to

wrong position. largest screw icon.

• Screws stripping. • Torque adjustment collar • Move collar position to

setting too high. a smaller screw icon.

• Screws not fully seated. • Torque adjustment collar • Move collar position to

setting too low. a larger screw icon.

• Screw holder not holding • Screw is non-ferrous. • Use ferrous screw.

screw.

For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with

this tool could be hazardous.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

lithium-ion battery (or battery pack) indicates that the costs to recycle the

battery (or battery pack) at the end of its useful life have already been paid

by Black & Decker. In some areas, it is illegal to place spent lithium-ion

batteries in the trash or municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent lithium-ion

batteries. Help protect our environment and conserve natural resources by returning the

tool to an authorized Black & Decker service center for recycling. You may also contact

your local recycling center for information on where to drop off the spent battery, or call

1-800-8-BATTERY.

• Slide screw holder arm back towards screwdriver bit. Ensure screwdriver bit tip and

screw head are fully engaged. (figure H)

• At this time the screw is being held securely to the screw holder carrier by means of an

internal magnet. Note: Magnet will not work on non-ferrous screws.

• Ensure unit is set for driving screws in the forward position.

• While driving the screw, the screw holder carrier and arm will retract allowing the screw

head to be driven to its desired depth (figure I).

• After use, return screw holder arm back into its storage position to protect screw holder

from damage.

Screw driving Notes:

• Do not use double ended screwdriver bits.

• Do not use screwdriver as a pry bar in any position.

• To avoid screwdriver being turned on accidentally, do not carry in your pocket.

LED LIGHT

A light (5) is built-in to the screwdriver above the spindle (6). To use the light without the

spindle turning, place the forward / reverse selector (2) in the neutral position.

DRILLING

• Insert the appropriate hex shank drill bit.

• Select the largest screw icon on the clutch collar for maximum torque.

• Select forward rotation.

NOTE: When drilling, the bit may become disconnected from the spindle upon

withdrawing it from the material. Should this occur, the bit can be removed by re-inserting

the hex shank into the spindle and running the tool in the reverse direction.

GENERAL DRILLING TIPS

• This tool is not recommended for drilling in masonry.

• Use sharp drill bits only.

• Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and

should be pulled out frequently when drilling to clear chips from the flutes.

• Support and secure work properly, as instructed in the safety Instructions.

• Use appropriate and required safety equipment, as instructed in the safety instructions.

• Secure and maintain work area, as instructed in the safety instructions.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting

but not so much as to stall the motor or deflect the bit.

• Hold the tool firmly to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED TOOL OFF AND ON IN AN ATTEMPT

TO START IT. DAMAGE TO THE TOOL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through last

part of hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce

jamming.

• Make sure switch turns tool on and off.

WARNING: It is important to support work properly and to hold the tool firmly to prevent

loss of control which could cause personal injury.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service personnel, always using identical replacement

parts.

90564630 li4000 revision.qxd:??????-00 BDL500 laser 5/25/10 7:45 AM Page 10

1 2

Troubleshooting 1
MODE DʼEMPLOI 2

Résumé du contenu

Page 1 - Troubleshooting

10 11TroubleshootingProblem Possible Cause Possible Solution• Battery will not charge. • Charger not plugged into • Plug charger into a a working outl

Page 2 - MODE DʼEMPLOI

N° de catalogue Li4000MODE DʼEMPLOITToouurrnneevviiss ssaannss ffiill aavveecc ppoorrttee--vviiss eessccaammoottaabblleeSERVICE INFORMATIONAll B

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 90564630 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Tournevis électriques Black & Decker 90564630. 90564630 li4000 revision.qxd:??????-00 BDL500 Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques Black & Decker 90564630