Black & Decker 5147205-00 Manuel d'instructions télécharger pdf (Page 2)

Safety Warnings and Instructions: Charging

1. This manual contains important safety and operating instructions.

2. Before using battery charger, read all instructions and cautionary warnings on battery

charger and product using battery. CAUTION: To reduce the risk of injury, use charger

only with this product. Batteries in other products may burst causing personal injury or

damage.

3. Do not expose charger to rain or snow.

4. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

7. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

8. Use only the supplied charger when charging your tool. The use of any other charger

could damage the tool or create a hazardous condition.

9. Use only one charger when charging.

10. Do not attempt to open the charger. There are no customer serviceable parts inside.

Return to any authorized Black & Decker service center.

11. DO NOT incinerate the tool or batteries even if they are severely damaged or

completely worn out. The batteries can explode in a fire.

12. Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created

when lithium ion battery packs are burned.

13. Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger

may ignite the dust or fumes.

14. If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for

three minutes or until irritation ceases. If medical attention is needed, the battery elec-

trolyte is composed of a mixture of liquid organic carbonates and lithium salts.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

Charging Procedure

THE BATTERIES IN YOUR TOOLARE NOT FULLY CHARGED AT THE FACTORY.

BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY

INSTRUCTIONS.

To charge your screwdriver, follow the steps below.

1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.

2. Place the screwdriver into the cradle making sure to match the charging

contacts on the handle of the screwdriver with the contacts in the charger. The red

(charging) light will illuminate indicating that the charging process has started.

3. Let the screwdriver charge initially for 9 hours. After the initial charge, under normal

usage, your tool should be fully charged in 6 hours.

Important Charging Notes

1. After normal usage, your tool should be fully charged in 6 hours. Your tool was sent

from the factory in an uncharged condition. Before attempting to use it, it must be

charged for at least 6 hours.

2. DO NOT charge the batteries in an air temperature below 40°F (4,5 °C) or above 105°F

(+40,5 °C). This is important and will prevent serious damage to the batteries. Longest

life and best performance can be obtained if batteries are charged when air

temperature is about 75°F.

3. While charging, the charger may hum and become warm to touch. This is a normal

condition and does not indicate a problem.

4. If the batteries do not charge properly—(1) Check current at receptacle by plugging in a

lamp or other appliance. (2) Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights. (3) Move charger and tool to a

surrounding air temperature of 40°F (4,5 °C) to 105°F (+40,5 °C). (4) If the charger is

mounted on a wall make sure the charge indicator light is on. If the indicator light

is not on, push unit down to make sure charging contacts are touching. (5) If the

receptacle and temperature are OK, and you do not get proper charging, take or send

the tool and charger to your local Black & Decker service center. See Tools Electric in

yellow pages.

5. The tool should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. DO NOT CONTINUE using product with its batteries in a

depleted condition.

6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30

days without use). Although extended charging is not a safety concern, it can significantly

reduce overall battery life.

Attaching Screwdriver Bit Tips Holder (Figure 1)

Attach the holder (K) to either side of the charging cradle (F) ( using the screw provided) as

shown in figure 1.

Wall Mounting (Figures 2, 3 & 4)

Use the hardware provided only if hanging on conventional sheet rock or plaster walls. If not

hanging on conventional sheet rock or plaster walls, please use the appropriate

fasteners for that material.

1. Attach the wall mount tool support (J) as shown in figure 2. CAUTION: The tool

support must be securely attached to the charging cradle when it is mounted on a

vertical surface.

2. Choose a location that is within reach of an electrical outlet. Fix the charging cradle (F)

as shown in figure 3 and 4.

NOTE: Avoid damaging the cord while fixing the charging cradle to the wall.

3. Plug in and place the product in position. Make sure the charge indicator light is on.

If the indicator light is not on, push unit down to make sure charging contacts are

touching.

Operating Instructions

Inserting an Accessory (Figure 5)

The LI3000 compact screwdriver is designed for use with screwdriver bits. Do not use

double ended screwdriver bits.

To install a bit simply insert it into the cavity in the hex spindle as shown in figure 5. To

remove the bit pull it straight out.

Switch (Figure 6)

To turn the tool ON in a forward direction, push the switch to the forward position(6A),

squeeze the trigger and the tool will run. Release pressure from the trigger and the tool will

stop.

To turn the tool ON in a reverse direction, push the switch to the rearward position(6B),

squeeze the trigger and the tool will run. Release pressure from the trigger and the tool will

stop.

With the switch in the middle position, the trigger will not be active and the spindle will be

locked (6C). Use the tool in this mode as any conventional non-powered screwdriver.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized

service centers or other qualified service organizations, always using identical replacement

parts.

Lubrication

Black & Decker tools are properly lubricated at the factory and are ready for use.

Accessories

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-54-HOW-TO. (800-544-6986) CAUTION: The use of any accessory or attachment

not recommended may be hazardous.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the

lithium-ion battery (or battery pack) indicates that the costs to recycle the

battery (or battery pack) at the end of its useful life have already been paid by

Black & Decker. In some areas, it is illegal to place spent lithium-ion batteries

in the trash or municipal solid waste stream and the RBRC program provides an

environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent lithium-ion

batteries. Help protect our environment and conserve natural resources by returning the tool

to an authorized Black & Decker service center for recycling. You may also contact your

local recycling center for information on where to drop off the spent battery, or call

1-800-8-BATTERY.

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers

with efficient and reliable power tool service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the Black & Decker location nearest you. To find

your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material

or workmanship. The defective product will be replaced or repaired at no charge in either of

two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should be

made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

the sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under

"Tools-Electric" in the yellow pages of the phone directory and available on our website

www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This

product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

Troubleshooting

Problem Possible Cause Possible Solution

• Unit will not start. • Battery not charged. • Check battery charging requirements.

• Battery will not charge. • Charger not plugged in. • Plug charger into a working outlet.

Refer to “Important Charging Notes” for

more details.

• Check current at receptacle by

plugging in a lamp or other appliance.

• Check to see if receptacle is

connected to a light switch which turns

power off when you turn out the lights.

• Surrounding air • Move charger and tool to a

temperature too hot or surrounding air temperature of

too cold. above 40 degree F(4,5°C)

or below 105 degree F (+40,5°C).

For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 5147205-00 Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis électriques Black & Decker 5147205-00