Black & Decker Fire Storm 90521841 Manuel d'instructions Page 5

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 28
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 4
5
4. Let the tool charge initially for 9 hours.
WARNING: When disconnecting the tool from the charger, be sure to unplug the charger
from the outlet first, then disconnect the charger cord from the tool cradle.
Important Charging Notes
1. After normal usage, your tool should be fully charged in 3 to 9 hours. If the batteries
are run down completely, it may take up to 9 hours to become fully charged. Your tool
was sent from the factory in an uncharged condition. Before attempting to use it, it
must be charged for at least 9 hours.
2. DO NOT charge the batteries in an air temperature below 40°F (4,5 °C) or above
105°F (+40,5 °C). This is important and will prevent serious damage to the batteries.
Longest life and best performance can be obtained if batteries are charged when air
temperature is about 75°F.
3. While charging, the charger may hum and become warm to touch. This is a normal
condition and does not indicate a problem.
4. If the batteries do not charge properly:
(1) Check current at receptacle by plugging in a lamp or other appliance.
(2) Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights.
(3) Move charger and tool to a surrounding air temperature of above 40 degree F
(4,5°C) or below 105 degree F (+40,5°C).
(4) If the receptacle and temperature are okay, and you do not get proper charging,
refer to your warranty.
5. The tool should be recharged when it fails to produce sufficient power on jobs which
were easily done previously. DO NOT CONTINUE using product with its batteries in a
depleted condition.
6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30
days without use). Although overcharging is not a safety concern, it can significantly
reduce overall battery life.
7. The batteries will reach optimum performance after being recharged 5 times during
normal usage. There is no need to run the batteries down completely before
recharging.
Hanging the Charging Base (fig. 2 & 3)
Use the hardware provided only if hanging on
conventional hollow wall construction such as sheet
rock or plaster walls. If not hanging on conventional
sheet rock or plaster walls, please use the
appropriate fasteners for that material.
The charger can be fixed to the charger mounting
bracket as described below, or simply placed, in a
convenient level position.
• Locate the charger mounting bracket within reach
of an electrical outlet.
• Mark the position of both hang holes as shown in
figure 2.
• The mounting screws should be driven in to about
an 1/8” (3mm) from the wall.
• Place the charger mounting bracket over the screw
heads and slide down until fully seated.
• Finish tightening the screws and check to see that
the bracket is firmly attached to the wall so it will not
pull out.
• Place the charger in position until it “clicks” into
place as shown in figure 3.
Safety Warnings and Instructions: Drilling
Hold tool firmly to control its twisting action.
WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To
reduce the risk of injury always expect the stall. Grip the tool firmly to control the
twisting action and prevent loss of control which could cause personal injury. If a stall
does occur, release the trigger immediately and determine the reason for the stall before
re-starting.
2
3
90521841 FSD600 6/20/07 10:34 AM Page 5
Vue de la page 4
1 2 3 4 5 6 7 8 9 10 ... 27 28

Commentaires sur ces manuels

Pas de commentaire