Black & Decker BDPS600 Manuel de service télécharger pdf (Page 13)

ENGLISH

(Original instructions)

Flushing the sprayer (g. Q & R)

u Disconnect the sprayer from the power supply.

u Unscrew the lid from the side of the canister and pour any

remaining liquid back into the original container (g. R).

u Pour a small amount of the appropriate cleaning solution

into the canister.

t Warm soapy water for water based materials.

t Manufacturers recommended cleaning solution for oil

based materials.

u Replace the lid (7) on the canister (6) securely and vigor-

ously shake the sprayer.

u Unscrew the lid (7) from the side of the canister and

properly dispose of cleaning solution.

u Rell the canister with a small amount of new cleaning

solution. Screw lid securely on canister.

u Reattach the sprayer to the motor unit, plug in the cord

and turn on the power unit.

u Switch the quick clean lever (1) from clean to paint. (g.Q)

u Spray the cleaning solution through the sprayer onto scrap

material for 5 seconds.

Cleaning the sprayer (g. S - X)

u Disconnect the sprayer from the power supply.

u Remove the side ll canister (6) and unscrew the side lid

(7). Remove the pickup tube (19) and o-ring (23) from the

sprayer. Clean the parts with the cleaning brush (14) in the

appropriate cleaning solution (g. S).

u Remove the front housing of the sprayer, by pressing

down on the release button (15) and pulling the front

housing off of the sprayer (g. T).

u Remove the piston (27) and spring (26) (g. U).

u Remove the spray nozzle (10 / 11), by turning counter-

clockwise, then remove the atomizer (24) (g. U).

u Clean the spray nozzle (10 / 11), pickup tube (19) and lter

(25), atomizer (24), piston (27) and spring (26) with the

cleaning brush (14) in the appropriate cleaning solution

(g. T).

u Thoroughly clean the inside of the piston chamber (28)

with the cleaning brush (14) (g. V)

Important : Be sure to remove all material from inside

of piston chamber. A small amount of material that is not

removed with the cleaning brush can harden over time and

interfere with the movement of the piston causing damage to

the sprayer.

u Switch the quick clean lever (1) from clean to paint.

u Thoroughly clean the inside of the intake (30) and return

(29) openings with the cleaning brush (g. W).

Important : Thoroughly clean the smaller vent hole (31), with

a pin or paper clip (g. X).

u Dry all parts thoroughly.

u Properly dispose of cleaning solution.

u Reassemble sprayer.

Reassembling the sprayer (g. Y & Z)

u Slide the spring (26) onto the front of the piston (27).

u Insert the piston and spring into the front housing.

u Pressing down on the release button (15), insert the front

housing with piston, into the sprayer until the release but-

ton pops into place.

u Place a few drops of oil through the cylinder opening. In-

sert the atomizer valve (24) into the front housing. Thread

the spray nozzle (10 / 11) onto the front housing and hand

tighten.

u Using the oil lubricant provided, place a few drops of

oil down the intake (30) and return (29) openings of the

sprayer.

u Rotate the quick clean lever (1) from paint to clean and

back 3 times after oiling.

u Insert the pickup tube (19) into the intake opening (30) on

the sprayer.

u Re-t the side ll canister.

Cleaning the power unit

u Turn the power unit off, unplug the cord and disconnect

the sprayer from the motor unit.

u Use only mild soap and damp cloth to clean the power

unit.

Warning! Never let any liquid get inside the power unit.

Warning! Never immerse any part of the power unit into a

liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

u Connect the green/yellow lead to the earth terminal.

Warning! Follow the tting instructions supplied with good

quality plugs. Recommended fuse: 13A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

Separate collection of used products and packaging

allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environ-

mental pollution and reduces the demand for raw

materials.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Black & Decker BDPS600 Manuel de service Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de pulvérisation fine de puissance Black & Decker BDPS600