Black & Decker BDPS600 Manuel de service télécharger pdf (Page 12)

ENGLISH

(Original instructions)

Hints for optimum use

Preparation tips

u Always stir and strain the material thoroughly before use.

u With any spraying job you should always ensure that

you have properly prepared the surface to get the best

nish. That is, all surfaces are free from dust, dirt, rust and

grease. Lightly pressure wash decks or exterior surfaces

and ensure that they are dry before spraying.

u It is recommended that you mask all edges and other

areas and use drop cloths to protect your oors and

anything else in the spraying area that you wish to remain

untouched.

u Skin that forms on the top of paint can clog the sprayer.

Remove skin before mixing. Strain with a funnel with a

lter attached or through hosiery to remove any impurities

that could clog system.

u Before starting have gloves, paper towels, rags etc. avail-

able for unexpected spills.

Developing the proper spraying technique (g. N & O)

u Practice spraying on a piece of scrap material such as

cardboard to test your spray pattern and become familiar

with the ow control feature of the sprayer.

u Ensure surface to be sprayed is free of dust, dirt, and

grease.

u Ensure spray area is clean and free of dust that could be

blown onto newly sprayed surfaces.

u Cover any areas not intended to be sprayed.

u Always spray from a minimum of 25mm to a maximum of

355mm (g. N).

u A commonly used method for spraying a large surface

is the “crisscross” pattern. This is done by spraying in

horizontal strips and then crossing over these strips with

vertical strips.

u To get an even spray distribution, always keep your arm at

the same distance (g. N) from the surface you are spray-

ing and avoid moving your wrist (g. O).

u Maintain smooth and consistent speed which will help

avoid inconsistencies. Begin spraying after the pass has

begun and release trigger before stopping the pass.

u Avoid spraying too heavily in any one area. Several lighter

coats are better than one heavy coat which can lead to

running and dripping. Remember that the ow control

knob regulates the amount of liquid that can be sprayed.

Turning the ow knob clockwise increases the ow of

liquid. Turning the knob counterclockwise decreases the

ow of liquid. If runs or drips do occur, have a dry paint

brush on hand to smooth them out.

u Turn the power unit off and place the sprayer in the built-in

dock of the power unit when not spraying for any length of

time.

Maintenance and cleaning

Your Black & Decker corded appliance has been designed to

operate over a long period of time with a minimum of main-

tenance. Continuous satisfactory operation depends upon

proper appliance care and regular cleaning.

Warning! Be sure to use appropriate personal protective

equipment.

Warning! Before performing any maintenance or cleaning on

corded appliances switch off and unplug the appliance.

Warning! Do not use materials with a ashpoint lower than

55°C. Flashpoint is the temperature that a uid can produce

enough vapours to ignite (see paint supplier instructions).

Warning! Make sure clean up area is well ventilated and free

of ammable vapours.

Warning! Always spray outdoors when spraying cleaning

solution through sprayer.

Warning! Do not submerse power unit.

Using the quick clean system (g. P & Q) (BDPS400

& BDPS600 only)

The quick clean system allows for a variety of useful functions.

First, the system can allow you to spray water or a suitable

cleaning liquid while there is still spray material in the main

canister. This is useful when setting up your spray pattern with

the fan nozzle. You can spray water instead of wasting spray

material to view the spray pattern.

Second, the quick clean system allows you to ush the pump

assembly, the piston, the nozzle and the atomizer valve. When

spraying for long periods of time, spray material may build

up causing a deterioration of the spray quality. It is good to

ush this system with water or cleaning liquid after every other

spray material rell. It is also important to ush the system

when the sprayer will sit for more than 15 minutes without use.

Spray material can dry on the nozzle and pump assembly and

would require a thorough cleaning. Always oil piston if sitting

idle for a long period of time. See “Reassembly Section”.

Third, the quick clean system allows for a faster clean-up

when your project is complete. One or two ushes through

the quick clean system gives you a head start on cleaning

the nozzle, the atomizer, the pump and piston. Please follow

recommended cleaning steps in this manual when performing

a nal clean of the system.

u Disconnect the sprayer from the power supply.

u Open the quick clean door (5), and pour in the cleaning

solution using the quick clean ll cup (16).

Warning! Do not overll the reservoir.

u Switch the quick clean lever (1) from paint to clean.

u Spray into a waste container, cardboard box or test

surface to completely ush the sprayer system.

u Repeat until the cleaning solution has returned to its

natural colour.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Black & Decker BDPS600 Manuel de service Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de pulvérisation fine de puissance Black & Decker BDPS600