Black & Decker GKC1817 Manuel de service télécharger pdf (Page 9)

(charging state) as the charger occasionally ‘tops off’

the battery charge.



The charging indicator will be lit as long as the battery

pack is connected to the plugged in charger.

Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charge indicators

If the charger detects a problem with a battery pack, the

charge indicator will flash at a fast rate.

 If this occurs, re-insert the battery pack (6).

 If the problem persists, put a different battery pack in the

charger to determine

if the charger is OK.



If the new battery pack charges correctly, then the

original battery pack is defective and should be returned

to a service centre for recycling.

 If the new battery pack gives the same indication as the

original, take the charger to be tested at an authorized

service centre.

Note: It may take as long as fifteen minutes to determine that

the pack is defective.

If the battery pack is too hot or too cold, the LED will

alternately blink fast and slow, one flash at each speed and

repeat.

Preparation

 Carry out regular cleaning of the unit as described in the

maintenance section and in particular cleaning inside

the chain access cover (11).

 The lower jaw (2) and top jaw (1) are designed to close

when one of the handles is released or when the piece

of branch being cut has been cut. If this does not occur,

discontinue use of the tool and remove the battery from

the tool.

 Check if any debris is blocking movement. To help in

this process it may be necessary to remove the chain

access cover (11). If on assembly the problem is still

present, return the unit to an authorised service centre.

Switchi

ng on and off

Warning! Never attempt to lock or fix a switch actuator in the

on position.

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently.

Switching on (fig. I)

Ensure a firm grip on the handles and then squeeze both

switch actuators (5) to switch the unit on.

Switching off (fig. I)

Release either of the switches.

Note: Both switches must be activated for the product to be

used.

Do not force the tool - allow it to do the work. It will do a better

d safer job at the speed for which it is designed. Excessive

force will stretch the saw chain.

If the saw chain (14) or guide bar (3) becomes jammed:



Switch the tool off.

 Disconnect the battery from the tool.

Open the cut with wedges to relieve the strain on the guide bar.

Do not try to wrench the saw free. Start a fresh cut.

Trimming branches (fig. J)

Ensure that there are no local by-laws or regulations that

would prohibit or control the trimming of the tree limbs.

 Make sure the tool is running at full speed before

making a cut.

 Hold the tool firmly in place to avoid possible bouncing

or sideways movement of the tool.



Guide the tool using light pressure.



Always cut down from the top. This way you will avoid

pinching the saw chain (14).

 Remove branches as shown in figure J. Starting from

the branch tip, reduce the branch in logical steps cutting

off small sections.

 Remove the tool from the cut while it is running at full

speed.

Maintenance

Your Black & Decker corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Be

fore performing any maintenance on corded/

cordless power tools:

 Switch off and unplug the appliance/tool.

 Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

 Or run the battery down completely if it is integral and

then switch off.

 Unplug the charger before cleaning it. Your charger

does not require any maintenance apart from regular

cleaning.

Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solve

nt-based cleaner.

Regularly open the chuck and tap it to remove any dust from

the interior (when fitted).

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GKC1817 Manuel de service Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à chaîne Black & Decker GKC1817