Black & Decker GKC1817 Manuel de service télécharger pdf (Page 6)



Keep your saw chain properly tensioned. Check tension

at regular intervals with the motor stopped and cord

disconnected.



Begin and continue cutting only with the chain moving at

full speed.

 Watch for shifting branches or other forces that could

close a cut and pinch or fall into the chain.



Use extreme caution when re-entering a previous cut.

Engage spikes on lower jaw into wood and allow the

chain to reach full speed before proceeding with cut.

 Use of this tool for operation different to those intended

could result in hazardous situations. Cut woo

d only.

Don't use this tool for purposes not intended - for

example - Don't use tool for cutting plastic, masonry or

non wood building materials.

 If any debris gets caught with the guard or tool

discontinue use, remove the battery and clear debris.

 Worn chains and chain guide bars should be replaced.

 Only use replacement bars and chains specified by the

manufacturer.

Safety of others



This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or ins

truction

concerning use of the appliance by a person

responsible for their safety.

 Children should be supervised to ensure that they do

not play with the appliance.

Vibration

The declared vibration emission values stated in the

technical data and the declaration of conformity have been

measured in accordance with a standard test method

provided by EN 60745 and may be used for comparing one

tool with another. The declared vibration emission value may

also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the

declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons

regularly using power tools in employment, an estimation of

vibration exposure should consider, the actual conditions of

use and the way the tool is used, including taking account of

all parts of the operating cycle such as the times when the

tool is switched off and when it is running idle in addition to

the trigger time

Labels on tools

The following symbols are found on your tool:

Residual risk

Despite the application of the relevant safety regulations and

the implementation of safety measures, certain residual risks

are inherent to the use of wood cutting saws and cannot be

avoided. These are:

 Risk of injury arising from contact with moving parts,

sharp parts, hot parts, branches or debris falling on the

operator, bystanders or property, debris ejected by the

tool.

 Risk of injury arising from un-intended use, falling from

a ladder or working position in a tree, damage to the

supply cable, use of the

tool in wet or hazardous

locations, use of the product by young children or infirm

persons, failure to wear suitable personal protection or

suitable clothing, breathing dust generated from cutting

wood.

The above risks have been addressed by including warnings

in the safety instructions and/or markings applied to the tool.

Additional safety instructions for batteries and chargers

Batteries



Never attempt to open for any reason.

 Do not expose the battery to water.

 Do not expose the battery to heat.

 Do not store in locations where the temperature may

exceed

40 °C.

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Do not use your saw in wet conditions or

expose it to rain.

Always wear head, hearing and eye protection.

Beware of falling objects.

Keep bystanders away.

Do not use on ladders.

Check the chain tension after every 10 minutes

of use. Adjust back to a clearance of 3 mm.

Oil the chain after every 10 minutes of use.

Warning do not touch chain at the chip ejection

point.

Direction of travel of the chain.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GKC1817 Manuel de service Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à chaîne Black & Decker GKC1817