Black & Decker 200 WATT Manuel d'utilisateur télécharger pdf (Page 7)

The handle assembly comprises the handle

tube (6), ‘T’ handle (7), which houses the

switch lever (8), safety lock-off switch (9) and

the electrical supply cable (10). A buckle

strap (11) is used to attach the electrical

supply cable to the handle tube.

The collection box assembly comprises the

collection box (12) which incorporates two

collection box support bars (13).

Assemble your raker, as follows:

• Place your raker body (1) in its working

position, on a level surface.

• Insert the handle tube (6) into your raker

body (1), locating the cross pin (17) in

the slot.

• With the cross pin (17) located in the slot,

place the handle plate (18) against your

raker body (1), aligning the two screw holes,

and secure the handle plate in position

using the two screws (19) provided.

• Place the ‘T’ handle (7) over the square

end of the handle tube (6) (Fig. B), with

the switch lever (8) on the right hand

side, slide the ‘T’ handle (7) down the

handle tube (6) until the holes in the ‘T’

handle and the handle tube are aligned.

• Fit the hexagon nut (20) into the

hexagonal recess on the underside of the

"T" handle. Insert bolt (21) into the

aligned holes and screw firmly into the

hexagon nut (20).

Note: If you have any difficulty inserting

the handle tube into the "T" handle,

loosen each of the screws at the end of

the "T" handle sufficiently to allow this.

When assembled, re-tighten the screws.

• Secure the electrical supply cable (10) to

the handle tube (6) using the buckle

strap (11) provided.

• Place the collection box (12) upside

down on a level surface, pass the

longest part of one of the collecting box

support bars (13) through the holes in the

side of the collection box (12), then rotate

the collection box support bar (13) in the

direction of the arrow until it clips into the

retainer on the collection box (12).

• Repeat this to fit the second collection

box support bar (13).

• With your raker in its working position, fit

the collection box (12) on to your raker

body (1), locating the collection box

support bars (13) into the pockets (22) at

the front of your raker.

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug (see

below). Brown is for “Live” (L) and blue is

for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

Fit a BS1363A

approved

resilient plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the recommended

fuse approved

to BS1362

Connect brown

to L (live)

230 volts AC only

Never use a light

socket

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable directly

into your raker yourself. Instead, take your

raker to your nearest Black & Decker

service agent.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA) circuit breaker in the house wiring.

If you do not have such a circuit breaker

installed, or you do not wish to have one

installed, then we strongly recommend that

the electrical power to your raker be supplied

through a high sensitivity residual current

device (RCD). The RCD is designed to

provide a high degree of personal protection

against harmful electric current should fault

conditions occur.

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

your raker from the safety instructions and

safe working practices given in this manual.

Assembly (Fig. A - D)

Remove all the parts of your raker from the

carton and familiarise yourself with the

individual parts of your raker.

The main parts of your raker are your raker

body (1) which houses the motor, front

wheels (2), tine assembly (3), and the rear

roller (4), which incorporates the three-

position height adjusters (5).

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Commentaires sur ces manuels

Pas de commentaire

Black & Decker 200 WATT Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Mini-faucheuses Black & Decker 200 WATT