Black & Decker IR05X Manuel d'utilisation et d'entretien

Naviguer en ligne ou télécharger Manuel d'utilisation et d'entretien pour Fers à repasser Black & Decker IR05X. Black & Decker IR05X Use & Care Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Please Read and Save this Use and Care Book.
IMPORTANT SAFETY
INSTRUCTIONS
When using your iron, basic safety precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING.
Use iron only for its intended use.
To protect against a risk of electric shock, do not immerse the
iron in water or other liquids.
The iron should always be turned to the minimum (min) setting
before plugging or unplugging from outlet. Never yank cord
to disconnect from the outlet; instead grasp plug and pull to
disconnect.
Do not allow cord to touch hot surfaces. Let iron cool completely
before putting away. Loop cord loosely around iron when storing.
Always disconnect iron from electrical outlet when lling with
water or emptying, and when not in use.
Do not operate iron with a damaged cord, or if the iron has been
dropped or damaged. To avoid the risk of electric shock, do not
disassemble the iron; take it to a qualied service person for
examination and repair, or call the appropriate toll-free number on
the cover of this manual. Incorrect reassembly can cause a risk
of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by
or near children. Do not leave iron unattended while connected or
on an ironing board.
Burns can occur from touching hot metal parts, hot water or
steam. Use caution when you turn a steam iron upside down or
use the surge of steam there may be hot water in the reservoir.
Avoid rapid movement of iron to minimize hot water spillage.
The iron must be used and rested on a stable surface.
When placing the iron on its stand, ensure that the surface on
which the stand is placed is stable.
The iron is not to be used if it has been dropped, or if there are
visible signs of damage or if it is leaking.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
The iron must be used and rested on a stable surface.
- When placing the iron on its stand, ensure that the surface on
which the stand is placed is stable.
- The iron is not to be used if it has been dropped, if there is
visible signs of damage or if it is leaking.
SPECIAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high-wattage
appliance on the same circuit.
If an extension cord is absolutely necessary, a cord with an
ampere rating equal to or greater than the maximum rating of the
iron should be used. A cord rated for less amperage can result in
a risk of re or electric shock due to overheating. Care shall be
taken to arrange the cord so that it cannot be pulled or be tripped
over.
SAVE THESE INSTRUCTIONS.
This product is for household use only.

This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit
into a polarized outlet only one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug in any way.

Warning: This appliance is equipped with a tamper-resistant screw
to prevent removal of the outer cover. To reduce the risk of fire or
electric shock, do not attempt to remove the outer cover. There are no
user-serviceable parts inside. Repair should be done only by authorized
service personnel.
Note: If the power-supply cord is damaged, it should be replaced
by qualified personnel, or in Latin America by an authorized service
center.

This appliance is intended for household use only.
GETTING STARTED
Remove any labels, stickers or tags attached to the body or soleplate of the
iron.
Please go to www.prodprotect.com/applica to register your warranty.
Note: Use ordinary tap water for ironing. Do not use water processed through
a home softening system.
Important: For optimum performance, let the iron stand for 90 seconds
before beginning to iron.
FILLING WATER TANK
1. With iron on flat surface with soleplate down, open
water-fill cover (A).
2. Tilt the iron and using a clean measuring cup, pour
water into opened chamber until water reaches the
MAX level mark on the side of the water tank. Do not
overfill.
3. Close the water-fill cover.
4. Plug in the iron. The power indicator light illuminates.
Note: If you need to add water while ironing, unplug the iron and follow above
steps.
Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or
hem) before ironing.
3-WAY AUTOMATIC SHUTOFF
The automatic shutoff feature in your iron works as fol-
lows:
Once the iron reaches appropriate temperature, it
will turn off after 30 seconds of inactivity if left on its
soleplate or tipped over on its side. If left vertically on
its heel rest, it will shut off after
8 minutes (B).
The power indicator light starts blinking to let you
know that the iron has stopped heating.
As soon as you pick up the iron, it will start heating again. Wait for iron to
reheat completely before resuming operation.
SMART STEAM® TECHNOLOGY
The Smart Steam® system automatically produces steam when you turn the
fabric select dial between settings 4 and 6.
SURGE OF STEAM
Horizontal
Tip: Use to remove stubborn creases.
1. With the water tank filled to the MAX mark, set fabric select dial to
appropriate setting (between 4 and 6) for your fabric. See fabric guide on
water tank and read garment’s label to help you determine fabric type.
2. Be sure there is water in the reservoir. Steam is automatically turned off
between settings 0 and 3.
3. For best performance, use surge of steam at 5-second intervals.
4. When finished ironing, turn the fabric select dial to 0 and unplug
the iron.
Important: Always stand the iron on its heel rest when powered on
but not in use.
Vertical
Tip: Use for removing wrinkles from hanging clothes and drapes.
1. Be sure the water tank is filled to the MAX mark.
2. Hang the garment to be steamed on a clothes hanger. (Curtains or drapes
can be steamed once they are hung.)
3. Set the fabric select dial to appropriate setting (between 4 and 6) for your
fabric.
4. Hold the iron close to, but not touching, the fabric.
5. Pull the fabric tight in your free hand and press the button as you move the
iron over the fabric.
USING SPRAY
Tip: Use to dampen tough wrinkles at any setting.
1. Be sure the iron is filled with water.
2. On first use, pump the button several times.
ANTI DRIP SYSTEM
The anti drip system prevents water spotting at low temperatures.
DRY IRONING
1. Turn the fabric select dial to setting 1, 2, or 3 to iron without steam.
2. To dry iron at higher settings, empty the water from the reservoir to prevent
steaming.
EMPTYING WATER TANK (OPTIONAL)
1. Unplug the iron and let it cool.
2. To release the water, hold the iron over a sink with the tip pointing down
and to one side. Water will empty out of the water-fill opening.

This product contains no user-serviceable parts. Refer service to qualified
service personnel.
CLEANING OUTSIDE SURFACES
Make sure iron is unplugged and has cooled completely. Wipe the sole-
plate and outer surfaces with a soft cloth dampened with water. Add mild
household detergent. Never use abrasives, heavy-duty cleansers, vinegar or
scouring pads that may scratch or discolor the iron.
After cleaning, steam iron over an old cloth to remove any residue from the
steam vents.
AUTO CLEAN® SYSTEM
Tip: To keep the steam vents free of any buildup, follow these instructions
about once a month:
1. Fill the water tank well below the MAX line. Plug in the iron.
2. Turn the fabric select dial to 6 and stand the iron on its heel rest. Allow it to
heat.
3. Turn fabric select dial to 0, unplug the iron and hold over a sink with the
soleplate facing down.
4. Press and hold the AUTO CLEAN® button. Be careful, as hot water
and steam will come out of the steam vents. Continue to hold the AUTO
CLEAN® button until all the water has emptied. If necessary, rock iron
side-to-side and front-to-back.
5. When finished, release the button, stand the iron on its heel rest and plug it
in. Heat for about 2 minutes to dry out any remaining water.
STORING YOUR IRON
1. Unplug the iron and allow it to cool.
2. Check that the selector is set to 0.
3. Store vertically on its heel to prevent water leaking from the soleplate.

For service, repair or any questions regarding your appliance, call the
appropriate 800 number on cover of this book. Please DO NOT return the
product to the place of purchase. Also, please DO NOT mail product back to
manufacturer, nor bring it to a service center. You may also want to consult
the website listed on the cover of this manual.
Two-Year Limited Warranty
(Applies only in the United States and Canada)
What does it cover?
Any defect in material or workmanship provided; however, Applica’s liability
will not exceed the purchase price of product.
For how long?
Two years from the date of original purchase with proof of such purchase.
What will we do to help you?
Provide you with a reasonably similar replacement product that is either
new or factory refurbished.
How do you get service?
Save your receipt as proof of date of sale.
Visit the online service website at www.prodprotect.com/applica, or call
toll-free 1-800-231-9786, for general warranty service.
If you need parts or accessories, please call 1-800-738-0245.
What does your warranty not cover?
Damage from commercial use
Damage from misuse, abuse or neglect
Products that have been modified in any way
Products used or serviced outside the country of purchase
Glass parts and other accessory items that are packed with the unit
Shipping and handling costs associated with the replacement of the unit
Consequential or incidental damages (Please note, however, that some
states do not allow the exclusion or limitation of consequential or incidental
damages, so this limitation may not apply to you.)
How does state law relate to this warranty?
This warranty gives you specific legal rights. You may also have other
rights that vary from state to state or province to province.
Por favor lea este instructivo antes de usar el producto.
INSTRUCCIONES
IMPORTANTES DE SEGURIDAD
Cuando se usan aparatos eléctricos, siempre se deben respetar
las siguientes medidas básicas de seguridad:
POR FAVOR LEA TODAS LAS INSTRUCCIONES ANTES DE USAR.
A n de protegerse contra el riesgo de un choque ectrico, no
sumerja la plancha en agua ni en ningún otro líquido.
La plancha siempre debe estar en la posición de calor mínimo
antes de enchufar o desconectarla del tomacorriente. Nunca tire
del cable para desconectar la plancha del tomacorriente; sujete
el enchufe y hale con cuidado.
No permita que el aparato entre en contacto con superficies
calientes. Espere que la plancha se enfríe por completo antes de
guardarla. Para guardar, enrolle el cable holgadamente en torno
a la plancha.
No permita que el cable cuelgue del borde de la mesa o del
mostrador ni que entre en contacto con las superficies calientes.
Siempre desconecte la plancha del tomacorriente cuando no esté
en uso y antes de llenar o vaciar el tanque de agua.
No use la plancha si tiene averiado el cable, si la ha dejado
caer o presenta cualquier otro daño. Para evitar el riesgo de
un choque ectrico, no desarme ni trate de reparar la plancha
personalmente. Acuda a un centro de servicio autorizado para
que la examinen, reparen o ajusten, o llame gratis al número
correspondiente en la cubierta de este manual. El reensamblaje
o reparacn incorrecta podría ocasionar el riesgo de incendio,
choque ectrico, o lesiones a las personas al usar el aparato
nuevamente.
Todo aparato eléctrico usado en la presencia de los nos o por
ellos mismos requiere la supervisión de un adulto. No desatienda
la plancha cuando esté conectada o sobre la tabla de planchar.
Las partes melicas calientes de este aparato, al igual que el
agua caliente o el vapor pueden ocasionar quemaduras. En vista
de que puede haber agua caliente en el tanque, tenga cuidado
A
B
8 minutes
30 seconds
al invertir una plancha de vapor o al bombear el botón de vapor.
Evite los movimientos rápidos de la plancha para disminuir el
goteo de agua caliente.
Este aparato no es diseñado para ser usado por personas
(incluído nos) con capacidad limitada fisica, mental o
sensoriales disminuidas y falta de experiencia o conocimiento
que les impida utilizar el aparato con toda seguridad sin
supervisión o instrucción.
Se debe asegurar la supervisión de los nos deben para evitar
que usen el aparato como juguete.
La plancha debe usarse o colocarse en una superficie plana y
firme.
- Cuando se coloca la plancha sobre el talón de descanso,
asegúrese de que la superficie sea plana y firme.
- La plancha no se debe usar si se ha caido, si se ha dañado o si
está goteando.
INSTRUCCIONES ESPECIALES
Para reducir la posibilidad de una sobrecarga ectrica, no opere
otro aparato de alto consumo en el mismo circuito.
Si el uso de un cable de extensión es absolutamente necesario,
se debeutilizar uno con un amperage igual o de más amperaje
que la plancha que se vaya a utilizar. Los cables de menor
amperaje se pueden sobrecalentar. Se debe tener cuidado de
acomodar el cable de manera que nadie lo hale o se tropiece
CONSERVE ESTAS
INSTRUCCIONES
Este aparato eléctrico es para uso
doméstico solamente.

Este aparato cuenta con un enchufe polarizado (un contacto es más
ancho que el otro). A fin de reducir el riesgo de un choque eléctrico,
este enchufe encaja en un tomacorriente polarizada en un solo
sentido. Si el enchufe no entra en el tomacorriente, invrtalo y si aun
así no encaja, consulte con un electricista. Por favor no trate de alterar
esta medida de seguridad.

Advertencia: Este aparato cuenta con un tornillo de seguridad para
evitar la remoción de la cubierta exterior del mismo. A fin de reducir el
riesgo de incendio o de choque eléctrico, por favor no trate de remover
la cubierta exterior. Este producto no contiene piezas reparables por
el consumidor. Toda reparación se debe llevar a cabo solamente por
personal de servicio autorizado.
Nota: Si el cordón de alimentación esta dañado, en América latina debe
sustituirse por personal calificado o por el centro de servicio autorizado.

Este producto es para uso dostico solamente.
PRIMEROS PASOS
Despegue toda calcomanía o etiqueta adherida al cuerpo o a la suela de a
plancha.
Por favor, visite www.prodprotect.com/applica para
registrar su garantía.
Nota: Utilice agua de la llave para llenar el tanque de la
plancha. No utilice agua procesada por un ablandador
de agua doméstico.
Importante: Para óptimo rendimiento, se
recomienda dejar reposar la plancha durante 90 segundos antes de
comenzar a planchar.
LLENADO DEL TANQUE DE AGUA
1. Posicione la plancha con la suela sobre una superficie plana, abra la tapa
del tanque según la ilustración (A).
2. Incline la plancha y con una taza de medir limpia, vierta agua en el orificio
hasta alcanzar la marca de llenado MAX en el tanque. No exceda el nivel de
llenado.
3. Cierre la tapa del tanque.
4.Enchufe la plancha. La luz indicadora de funcionamiento se ilumina.
Nota: Si tiene que agregar agua al tanque durante el planchado, desconecte
la plancha y siga los pasos citados anteriormente.
Consejo: Para evitar daño a las prendas, si desconoce la fibra de cierto
tejido, ensaye primero sobre una superficie pequeña y planche una costura o
ruedo interior.
APAGADO AUTOMÁTICO DE 3 POSICIONES
El dispositivo de apagado automático de esta plancha funciona de la siguiente
manera:
La plancha se apaga automáticamente si permanece inactiva sobre la
suela o de lado durante 30 segundos después de alcanzar la temperatura
programada. Igualmente sucede si la plancha permanece inactiva
verticalmente sobre el talón de descanso durante 8
minutos (B).
La luz indicadora de funcionamiento parpadea,
indicando que la plancha ha dejado de calentar.
La plancha comienza a calentar nuevamente en
cuanto uno la levanta. Espere que la plancha se
caliente bien antes de planchar.
TECNOLOGÍA SMART STEA
El sistema Smart Steam® produce vapor automáticamente cuando uno
ajusta el selector de tejidos entre el nivel 4 y 6.
EMISIÓN DE VAPOR
Horizontal
Consejo: Apropiado para suavizar las arrugas persistentes.
1. Llene el tanque de agua hasta alcanzar la marca de llenado MAX y ajuste
el selector de tejidos entre el nivel 4 y 6, según el tejido de la prenda.
Consulte la guía de tejidos en el tanque de agua y lea la etiqueta de la
prenda para determinar el tipo de tejido.
2. Asegúrese de que haya agua en el tanque. La emisión de vapor se apaga
automáticamente entre el nivel 0 y 3.
3. Para mejor rendimiento, utilice la emisión de vapor en intervalos de 5
segundos.
4. Cuando termine de planchar, ajuste el selector de tejidos a la posición “0
y desconecte la plancha.
Importante: Siempre coloque la plancha sobre el talón de descanso
cuando esté encendida o no en uso.
Vertical
Consejo: Ideal para suavizar las arrugas de las prendas colgantes o de las
cortinas.
1. Aserese de que el tanque de agua esté lleno hasta el nivel MAX.
2. Cuelgue la prenda que desea vaporizar en un gancho. (Uno puede vaporizar
las cortinas una vez instaladas).
3. Ajuste el selector al nivel apropiado (entre el 4 y 6), según el tejido.
4. Sujete la plancha cerca, pero no en contacto con el tejido.
5. Hale el tejido con una mano y bombee el botón con la otra, a medida pasa
la plancha sobre la prenda.
USO DEL ROCIADOR
Utilice a cualquier nivel de temperatura para humedecer las arrugas persis-
tentes.
1. Aserese de que el tanque de agua esté lleno.
2. Para el primer uso, bombee el botón varias veces.
SISTEMA ANTIGOTEO
El sistema antigoteo evita las manchas de agua que puede ocasionar la
plancha a temperaturas bajas.
PLANCHADO A SECO
1. Ajuste el selector de tejidos a la posición 1, 2 o 3 a fin de planchar sin
vapor.
2. Si desea planchar a seco a temperaturas más elevadas, vacíe el tanque por
completo para evitar la emisión de vapor.
VACIADO DEL TANQUE (OPCIONAL)
1. Desconecte la plancha y permita que se enfríe.
2. Si desea vaciar el agua, sujete la plancha sobre un fregadero con la punta
hacia abajo y hacia un lado.
3. El agua sale a través del orificio de llenado.

Este producto no contiene partes que el consumidor pueda reparar. En caso
de requerir mantenimiento, envíela al personal de servicio calificado.
LIMPIEZA DE LAS SUPERFICIES EXTERIORES
1. Asegúrese de desconectar y permitir que la plancha se enfríe bien. Limpie
la suela y las superficies exteriores con un paño suave, humedecido
con agua y un detergente doméstico suave. Jamás utilice abrasivos,
limpiadores fuertes, vinagre ni almohadillas de fregar que puedan rallar o
decolorar la plancha.
2. Después de limpiar, planche a vapor sobre un paño viejo a fin de retirar
todo residuo acumulado en los orificios de vapor.
LIMPIEZA AUTOMÁTICA (AUTO CLEAN®)
A fin de mantener los orificios de vapor libres de acumulaciones, siga las
siguientes instrucciones por lo menos una vez al mes:
1. Llene el tanque de agua por debajo de la línea MAX.
2. Enchufe la plancha.
3. Ajuste el selector de tejidos al nivel 6 y coloque la plancha sobre el talón de
descanso. Permita que la plancha se caliente.
4. Gire el selector de tejidos a la posición “0”, desconecte y sujete la plancha
sobre un lavabo con la suela orientada hacia abajo. Presione y sostenga el
botón de limpieza automática (AUTO CLEA). Tenga cuidado del agua
caliente y del vapor que emiten los orificios de vapor. Continúe sosteniendo
el botón de limpieza automática (AUTO CLEAN®) hasta haber vaciado toda
el agua. Si es necesario, mueva la plancha de lado a lado y de atrás para
adelante.
5. Al terminar, suelte el botón, coloque la plancha sobre el talón de descanso
y enchúfela. Permita que la plancha se caliente unos dos minutos hasta
secar toda el agua sobrante.
ALMACENAMIENTO DE LA PLANCHA
1. Desconecte la plancha y espere que se enfríe.
2. Verifique que el selector de temperatura es ajustado a la posición “0.
3. Almacene la plancha verticalmente sobre el talón de descanso, a fin de
evitar el goteo a través de la suela.

Para servicio, reparaciones o preguntas relacionadas al producto, por favor
llame al número del centro de servicio que se indica para el país donde usted
compró su producto. NO devuélva el producto al fabricante. Llame o lleve el
A
B
8 minutes
30 seconds
Vue de la page 0
1 2

Résumé du contenu

Page 1 - 30 seconds

Please Read and Save this Use and Care Book.IMPORTANT SAFETY INSTRUCTIONSWhen using your iron, basic safety precautions should always be followed, in

Page 2 - CONSERVER CES MESURES

2012-10-4_22 E/S/F© 2013 Applica Consumer Products, Inc.Model/Modelo/ Modèle: IR05X, IR06X, IR07X, IR08X, IR09XCustomer Care Line: 1-800-231-9786For

Commentaires sur ces manuels

Pas de commentaire