Black & Decker PLR36NC Manuel de service Page 6

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 38
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 5
6
To switch the tool on, press the on/off switch (1).
To switch the tool off, release the on/off switch (1).
LED LIGHT
The LED light (6) is activated automatically when the
on/off switch (1) is depressed. The LED light will also
activate when the forward/reverse slider (2) is set to the
centre position and the on/off switch (1) is depressed.
HINTS FOR OPTIMUM USE
Let the tool work at its own pace. Do not overload.
Always use the correct type and size of screwdriver
bit.
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
Use the auto spindle lock to loosen very tight screws
or to firmly tighten screws.
Always hold the tool and screwdriver bit in a straight
line with the screw.
When screwing in wood, it is recommended to drill a
pilot hole with a depth equal to the length of the
screw. A pilot hole guides the screw and prevents
splintering or distortion of the wood. For the optimum
size of the pilot hole, refer to the table below.
When screwing in hardwood, also drill a clearance
hole with a depth equal to half the length of the
screw. For the optimum size of the clearance hole,
refer to the table below.
MAINTENANCE
Your Black & Decker power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
Regularly clean the motor housing using a damp
cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any
dust from the interior.
This tool is not user-serviceable. Take it to an authorized
Black & Decker repair agent for service.
Your charger does not require any maintenance apart
from regular cleaning.
IMPORTANT
To ensure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in
this manual) should be performed by authorized service
centers or other qualified organizations, always-using
identical replacement parts. Unit contains no user
serviceable parts inside.
CLEANING
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen collecting in
and around the air vents. Wear approved eye protection
and approved dust mask when performing this
procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the tool.
These chemicals may weaken the materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease may
be removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
ACCESSORIES
The performance of your tool depends on the accessory
used. Black & Decker and Piranha accessories are
engineered to high quality standards and designed to
enhance the performance of your tool. By using these
accessories you will get the very best from your tool.
Black & Decker offers a large selection of accessories
available at our local dealer or authorized service center
at extra cost.
CAUTION: The use of any other accessory not
recommended for use with this tool could be hazardous.
PROTECTING THE ENVIRONENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker
product needs replacement, or if it is of no further use to
you, do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
s
s
s
s
s
s
s
s
s
s
s
s
s
ENGLISH
Screw size
No. 6 (3.5 mm)
No. 8 (4 mm)
No. 10 (5 mm)
Pilot hole
(softwood)
2.0 mm
3.2 mm
3.5 mm
Pilot hole
(hardwood)
2.5 mm
3.5 mm
4.0 mm
Clearance hole
4 mm
5.0 mm
5.7 mm
㱵㱵
Vue de la page 5
1 2 3 4 5 6 7 8 9 10 11 ... 37 38

Commentaires sur ces manuels

Pas de commentaire