Black & Decker PLR36NC Manuel de service télécharger pdf (Page 5)

CHARGERS

Use your Black & Decker charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and

damage.

Never attempt to charge non-rechargeable batteries.

Have defective cords replaced immediately.

Do not expose the charger to water.

Do not open the charger.

Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

The charger automatically shuts off if the ambient

temperature becomes too high. As soon as the

ambient temperature has cooled down, the

charger will resume operating.

Charge only at ambient temperatures between

10 °C and 40 °C.

Charging

ELECTRICAL SAFETY

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

If the supply cord is damaged, it must be replaced by

the manufacturer or an authorised Black & Decker

Service Centre in order to avoid a hazard.

Warning! Never attempt to replace the charger unit with

a regular mains plug.

FEATURES(fig. A and B)

1. On/off switch

2. Forward/reverse slider

3. Pivot release button

4. Bit storage

5. Bit holder

6. LED light

7. Charger

8. Charger plug

9. Charger connector

ASSEMBLY

FITTING AND REMOVING A DRILL BIT OR A

SCREWDRIVER BIT (fig. B)

This tool uses screwdriver bits and drill bits with a 6.35

mm (1/4") hexagonal shank.

To fit a bit, insert the bit shaft into the bit holder (5)

until it locks into place.

To remove a bit, pull the bit shaft out of the bit holder

(5).

USE

Before ﬁrst use, the battery must be charged for 17

hours.

The battery needs to be charged before ﬁrst use and

whenever it fails to produce sufﬁcient power on jobs

that were easily done before. When charging the

battery for the ﬁrst time, or after a prolonged storage,

it will only accept an 80% charge. After several

charges and discharge cycles, the battery will attain

full capacity.

CHARGING THE BATTERY (FIG. A)

To charge the battery, insert the charger plug (8) into

the connector (9).

Plug in the charger (7).

Leave the tool connected to the charger for 17 hours.

The charger may hum and become warm while

charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient

temperatures below 10 °C or above 40 °C.

SELECTING THE DIRECTION OF ROTATION

For tightening screws, use forward (clockwise) rotation.

For loosening screws use reverse (counterclockwise)

rotation.

To select forward rotation, push the forward/reverse

slider (2) to the forward position.

To select reverse rotation, push the forward/reverse

slider (2) to the rearward position.

To lock the tool, set the forward/reverse slider into

the centre position.

SPINDLE LOCK

This tool is ﬁtted with a spindle lock so that it can be

used as a normal screwdriver. Use the tool this way to

loosen very tight screws or to ﬁrmly tighten screws.

PIVOTING THE TOOL HEAD (FIG. C & D)

The tool is ﬁtted with a tool head that can be pivoted for

optimum versatility.

Push the pivot release button (3).

Pivot the tool head to the inline position (ﬁg. D).

Release the pivot release button (3).

Warning! Ensure the tool head is locked into place before

use.

SCREWDRIVING

Select forward or reverse rotation using the forward/

reverse slider (2).

ENGLISH

1 2 3 4 5 6 7 8 9 10 ... 37 38

Commentaires sur ces manuels

Pas de commentaire

Black & Decker PLR36NC Manuel de service Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis sans fil Black & Decker PLR36NC