Black & Decker HP186F4L Manuel d'instructions télécharger pdf (Page 8)

Fitting and removing a drill bit or screwdriver bit

(g. D)

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Open the chuck by turning it (3) with one hand while

holding the tool with the other.

u Insert the bit shaft (14) into the chuck.

u Firmly tighten the chuck by turning it (3) with one hand

while holding the tool with the other.

This tool is supplied with a double-ended screwdriver bit in the

bit holder (6).

u To remove the screwdriver bit from the bit holder, lift the bit

from the recess.

u To store the screwdriver bit, rmly push it into the holder.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 60 °C.

The battery should be left in the charger and the charger will

begin to charge automatically when the cell temperature

warms up or cools down.

u Plug in the charger (8) and switch on at the mains.

u Insert the battery (7) into the charger. Make sure that the

battery is fully seated in the charger (8).

The charging indicator (10) will ash continuously (slowly). The

charge is complete when the charging indicator (10) lights

continuously. The charger and the battery can be left connected

indenitely with the LED illuminated. The LED will change to

ashing (charging) state as the charger occasionally tops off the

battery charge. The charging indicator (10) will be lit as long as

the battery is connected to the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charging indicators

If the charger detects a problem with the battery, the charging

indicator (10) will ash at a fast rate. Proceed as follows:

u Re-insert the battery (7).

u If the charging indicators continues ashing at a fast rate,

use a different battery to determine if the charging process

works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 15 minutes to determine that the

battery is defective. If the battery is too hot of too cold, the

LED will alternately blink fast and slow, one ash at each

speed and repeat.

Selecting the direction of rotation (g. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the operating mode or torque (g. F)

This tool is tted with a collar to select the operating mode and

to set the torque for tightening screws. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. The collar has a wide

range of settings to suit your application.

u For drilling in wood, metal and plastics, set the collar (4) to

the drilling position by aligning the symbol with the

marking (15).

u For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

- Set the collar (4) to the lowest torque setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

HP148F4L/HP188F4 - Drilling in masonry (g. F & G)

u For drilling in masonry, set the collar (4) to the hammer

drilling position by aligning the symbol with the marking

(15).

u Slide the two-gear selector (5) towards the front of the tool

(2nd gear).

Two-gear selector (g. G)

u For drilling in steel and for screwdriving applications, slide

the two-gear selector (5) towards the rear of the tool (1st

gear).

u For drilling in materials other than steel, slide the two-gear

selector (5) towards the front of the tool (2nd gear).

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Black & Decker HP186F4L Manuel d'instructions Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Tournevis sans fil Black & Decker HP186F4L