Black & Decker GTC650L Manuel d'instructions télécharger pdf (Page 8)

ENGLISH

(Original instructions)

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (9) will ash red at a fast rate. Proceed as

follows:

♦ Re-insert the battery (6)

♦ If the charging indicator continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

♦ If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

♦ If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

service centre.

Note It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Switching on and off (g. C)

For your safety, this tool is equipped with a double switching

system. This system prevents starting the tool inadvertently

and will only allow operation while holding the tool with both

hands.

Switching on

♦ Squeeze the front handle switch (1).

♦ Push the lock-off button (3) forward using your thumb and

at the same time squeeze the trigger switch (2).

♦ Release the lock-off button.

Switching off

♦ Release the front handle switch (1) or the trigger switch (2).

Warning! Never attempt to lock a switch in the on position.

Hints for optimum use

♦ Slightly tilt the tool (up to 15° relative to the line of cut) so

that the blade tips point slightly towards the hedge (g. D1).

This will cause the blades to cut more effectively.

♦ Start by trimming the top of the hedge. Hold the tool at

the desired angle and move it steadily along the line of

cut (g. D2). The double-sided blade allows you to cut in

either direction.

♦ In order to obtain a very straight cut, stretch a piece of

string along the length of the hedge at the desired height.

Use the string (11) as a guideline, cutting just above it (g. D2).

♦ In order to obtain at sides, cut upwards with the growth

(g. D3). Younger stems move outwards when the blade

cuts downwards, causing shallow patches in the hedge.

♦ Take care to avoid any foreign objects. Especially avoid

hard objects such as metal wire and railings, as these

could damage the blades (g. D4).

♦ Regularly oil the blades.

♦ Consider purchasing a spare battery to extend the

running time of this tool. The catalogue number of the

battery is found in the technical data chart below.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Before performing any maintenance on corded/cordless power

tools:

♦ Switch off and unplug the appliance/tool.

♦ Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

♦ Or run the battery down completely if it is integral and

then switch off.

♦ Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth. Do not

use any abrasive or solvent-based cleaner.

Regularly open the chuck and tap it to remove any dust from

the interior (when tted).

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product

available for separate collection.

Separate collection of used products and

packaging allows materials to be recycled and

used again. Re-use of recycled materials helps

prevent environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Black & Decker GTC650L Manuel d'instructions Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Taille-haie sans fil Black & Decker GTC650L